Protecting Your
Digital Assets
™
Protecting Your
Digital Assets
™
CRU DataPort
®
41 Enclosure
Thank you for purchasing CRU’s DataPort 41 enclosure. The DataPort
41 enclosure is a sturdy aluminum 4-bay removable drive enclosure that
mounts in a 5.25” drive bay and accepts 2.5” hard disk drives or solid state
drives. The drives used in a DataPort 41 enclosure operate independently
of each other and can be inserted and removed from the front of the unit
without having to remove the enclosure from its bay or having to open
the computer case. With 4 dedicated 6 Gbps chips on board, 10 LED
indicator lights, and dual-4cm magnetic levitation fans, the DataPort 41 is a
convenient and powerful enclosure for any system.
Features
•
Holds up to four 2.5” SAS or SATA hard drives at the same time
that can be inserted and removed independently
•
Each drive runs at 6 Gbps
•
All 4 drives have dedicated Power and Drive Activity LEDs
•
Compact storage enclosure that mounts inside any standard 5.25”
drive bay
©2014 CRU Acquisition Group LLC, ALL RIGHTS RESERVED. DataPort
®
and CRU
®
are trademarks of CRU Acquisition Group, LLC and are
protected by trademark law.
Product Warranty
CRU warrants this product to be free of significant defects in material and workmanship for a period of 3 years from the original date of pur
-
chase. CRU’s warranty is nontransferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warranties. CRU expressly disclaims all other warranties, including but not limited
to, the implied warranties of merchantability and fitness for a particular purpose and non-infringement of third-party rights with respect to
the documentation and hardware. No CRU dealer, agent, or employee is authorized to make any modification, extension, or addition to this
warranty. In no event will CRU or its suppliers be liable for any costs of procurement of substitute products or services, lost profits, loss of
information or data, computer malfunction, or any other special, indirect, consequential, or incidental damages arising in any way out of the
sale of, use of, or inability to use any CRU product or service, even if CRU has been advised of the possibility of such damages. In no case shall
CRU’s liability exceed the actual money paid for the products at issue. CRU reserves the right to make modifications and additions to this
product without notice or taking on additional liability.
FCC Compliance Statement:
“This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.”
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a home or commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
In the event that you experience Radio Frequency Interference, you should take the following steps to resolve the problem:
1)
Ensure that the case of your attached drive is grounded.
2)
Use a data cable with RFI reducing ferrites on each end.
3)
Use a power supply with an RFI reducing ferrite approximately 5 inches from the DC plug.
4)
Reorient or relocate the receiving antenna.
Product Models
DataPort 41
Interface Types & Speeds
SATA: up to 6 Gbps
SAS: up to 6 Gbps
Drive Types Supported
2.5” SAS or SATA hard drives up to 15mm in height
Data Connectors
•
Two (2) SATA data connectors
• Two (2) SAS/SATA unified power and data connectors
• One (1) 5-pin JST error connector (user defined)
Operating System
Requirements
•
Windows 8, 7, or Vista
• Windows Server 2012, 2008, or 2003 product families
•
Mac OS X 10.4.x or higher
•
Linux distributions that support the connection type used
Torque
2.5-inch hard drives, M3 screws: 4 inch-pounds max.
Compliance
EMI Standard: FCC Part 15 Class B, CE
EMC Standard: EN55022, EN55024
Product Weight
2.80 pounds (complete assembly without hard drives)
Product Dimensions
5.76” x 1.65” x 6.17” (146mm x 42mm x 157mm)
Technical Support
Your investment in CRU products is backed up by our free technical
support for the lifetime of the product. Contact us through our website,
cru-inc.com/support
or call us at 1-800-260-9800 or +1-360-816-1800.
A5-041-0001-1 Rev. 1.1
FOR HOME OR OFFICE USE
