background image

INTERFACING SOLUTIONS

RVCFD-79

REAR-VIEW INTEGRATION INTERFACE

FOR FORD & LINCOLN VEHICLES 2011-UP

W/ MYFORD TOUCH RADIOS

FORD
2011 - 2014  Edge 
2011 - 2014  Explorer 
2012 - 2014  Focus
2013 - 2014  Focus ST (MUST Tap 12V Power for Camera from Reverse Light) 
2013 - 2014  Taurus
2013 - 2014  Escape
2013 - 2014  F-150
2013 - 2014  F-150 Raptor
2013 - 2014  F-250
2013 - 2014  F-350
2013 - 2014  F-450
2013 - 2014  F-550
2013 - 2014  Fusion Hybrid
2013 - 2013  Fusion Energy
2013 - 2014  C-Max Hybrid
2013 - 2014  C-Max Energy

LINCOLN
2011 - 2014  MKX
2013 - 2014  MKS
2012 - 2014  MKT

Disclaimer:  Depending on the HW version of your MyFord Touch system, this product may not support 
some older versions. Please contact us for more information.

WORKS FOR:

FORD = SONY 8” RADIOS

LINCOLN = NON-SONY 8” RADIOS

This interface does not o er the 

Force RVC feature. 

PARTS INCLUDED
(1) FD-79 C-500 Interface Module
(1) FD-79 C-125 Interface Module
(1) FD-79 54-Pin T-Harness
(1) Instruction Sheet

SAFETY PRECAUTIONS
1. Please read through the entire instruction manual before starting any of the installation procedures.
2. We recommend disconnecting the negative side of the battery until ready to code the vehicle.
3. Do not install any of the main modules near any major components or near the HVAC system,
    as placing items near the HVAC may cause damage or overheating to the vehicle or interface.
4. We recommend not disconnecting any of the air bag connections behind the dash panels.
5. This product is under Crux’s 1 year manufacturer’s warranty. Warranty may be voided in the case where 
    the device shows proof of being opened or improper extreme force.

TECH SERVICES
All our products are manufactured under strict quality control. Each device is being tested before shipment. If nevertheless do occur problems or if 
you have technical questions, contact us directly:

Crux Interfacing Solutions Tech Support
1 (855) 822-1348 (Mon - Fri - 9:00 AM - 5:00 PM) 

 Time

www.cruxinterfacing.com

Rev. 072214

1

Uninstall the RVCFD-79 before

performing a vehicle system reflash.

Reinstall the RVCFD-79 afterwards.

NOTE:

Summary of Contents for RVCFD-79











Reviews: