background image

PORSCHE

2013 - 2015  911
2014 - 2015  Boxster
2008 - 2015  Cayenne
2014 - 2015  Cayman
2010 - 2015  Panamera

Disclaimer:

 Depending on the HW version of your PCM system, this product may not support some  versions. 

Internal DVD player will not be  able to be watched while in  motion.

SAFETY PRECAUTIONS

1. Please read through the entire instruction manual before starting any of the installation procedures.
2. We recommend disconnecting the negative side of the battery until ready to code the vehicle.
3. Do not install any of the main modules near any major components or near the HVAC system,
    as placing items near the HVAC may cause damage or overheating to the vehicle or interface.
4. We recommend not disconnecting any of the air bag connections behind the dash panels.
5. This product is under Crux’s 1 year manufacturer’s warranty. Warranty may be voided in the case where 
    the device shows proof of being opened or improper extreme force.

2015  911 GT3

2014 -

APPLICATION NOTES:

ONLY FOR VEHICLES WITHOUT FACTORY REAR-VIEW CAMERA

WORKS FOR:

PCM 3.1 NAVIGATION RADIOS

PCM 3.0 NAVIGATION RADIOS (Cayenne Only)

(from Software Version 4.xx ONLY)

(from Software Version 4.xx ONLY)

(from Software Version 4.xx ONLY)

Rear-View Integration Interface for

PORSCHE Vehicles with PCM-3 or PCM-3.1 Systems

PCM-3

R

INTERFACING SOLUTIONS

Sightline

REAR-VIEW INTEGRATION

Crux Interfacing Solutions • 6860 Canby

 Ave., Suite 1

16, Reseda, C

A  91335

phone: (818) 609-9299 • fax: (818) 996-8188 • www

.cruxinterfacing.com

1 of 10

rev.051718

Summary of Contents for Sightline PCM-3











Reviews: