background image

User Manual

Compliance ..........................................................2

Warranty information .........................................2

Introduction
 

D-fend™ overview .........................................3

 

Typical applications ........................................3

 

What NOT to do with D-fend™ ......................3

 

“Use your ears” ..............................................4

Product Description 
 

Front LED legend ............................................4

 

NL4 connectors ..............................................4

Specifications ......................................................5

Terms and Definitions ........................................6

USB Connection ..................................................9

Typical System Configurations
 Subwoofers ....................................................10
 

Full system .....................................................11

 

Tweeter only ..................................................12

 

Distributed 20-70-100 volt .............................13

 
Setup Wizard .......................................................14

Mounting Recommendation..............................17

Advanced Programming ....................................18
 

Dual sub .........................................................20

 

Full system .....................................................21

 

Tweeter protection ........................................25

 

Distributed systems .......................................26

Troubleshooting ..................................................27
 
Technical Support ...............................................28
 
 

© 2013 Eminence Speaker LLC.  All rights reserved. D-fend™ is a trademark of Intrinsic Audio Solutions, Inc., D.B.A SLS Audio.

Do not assume the SA300 is sufficiently programmed right out of the box without any additional 
configuration via the set-up Wizard or Advance Programming window.  The unit ships with default 
settings intended for quality assurance testing purposes only.

stand alone unit

power handling:

4,000W @ 8Ω | 2,000W @ 4Ω | 1,250W @ 2Ω

SA300

Summary of Contents for SA300





























Reviews: