background image

SPECIFICATION DATA

ADVANTAGE

®

 DELUXE 

ELECTROL

®

Automatic Electric Projection Screen Model

S

UGGESTED SPECIFICATIONS: 

 

 projection screen(s), 

(H) x  

  (W).  The  Advantage

®

 Deluxe 

Screen shall have two motors, one to operate door and one to operate screen. Door motor electrically operated 120 volt (60 Hz) not more 

than 1.2 amp, mounted inside the roller, to be three wire with ground, quick reversal type, oiled for life, with automatic thermal overload 

cutout, integral gears, capacitor and an electric brake to prevent coasting. To have pre-set but adjustable limit switches to automatically 

stop fabric door in the ”down“ position. The door will lift to the closed position where a micro switch shall cut off the electrical current to 

the door motor. Screen motor is electrically operated 120 volt (60 Hz) not more than 2.4 amp, mounted inside the roller, to be three wire 

with ground quick reversal type, oiled for life, with automatic thermal overload cutout, integral gears, capacitor and an electric brake to 

prevent coasting. To have pre-set but adjustable limit switches to automatically stop picture surface in the ”up“ and ”down“ positions. 

The roller to be of rigid metal. Screen fabric to be flame retardant and mildew resistant fiberglass with black masking borders standard. 

Bottom of fabric shall be formed into a pocket holding a metal rod with plastic caps. Case shall be a white powder coated aluminum 

extrusion. Bottom of case to be self-trimming with a built-in flange around the bottom of the case. A section of the bottom of the case 

shall be an aluminum door equipped with concealed hinges so that it opens and closes automatically with the lowering and raising of the 

picture surface. The balance of the bottom of the case shall be a second hinged aluminum door with manual opening to provide access. 

Junction box shall be internally integrated into the housing making it possible to install the housing and wire to the building’s electrical 

system during construction. The junction box shall contain a quick connect connector that is mounted in the housing for easy plug-in 

connection to the motorized fabric and roller assembly. The motorized fabric and roller assembly to be installed in the case at the factory 

or at a later time at the job site. To be complete with integrated low voltage control unit and three position control switch with cover 

plate. Suitable for use in environmental air space in accordance with section 300-22 (c) of the National Electric Code, and sections 2-128, 

12-010 (3) and 12-100 of the Canadian Electrical Code, part 1, CSA C22.1. Screen to be listed by Underwriters’ Laboratories.

9

1

/

4

"

(SUGGESTED) 

3

/

8

THREADED ROD 

(NOT INCLUDED) 

ATTACHED TO 

MOUNTING 

BRACKET

FINISHED 
CEILING

SELF-TRIMMING 
FLANGE

7

1

/

4

"

8

3

/

4

"

CASE LENGTH

VARIABLE POSITION 

MOUNTING BRACKETS

7

1

/

4

"

7

1

/

4

"

6

1

/

8

"

MOTOR END

6

1

/

8

"

ELECTRICAL 

JUNCTION BOX

DOOR
ROLLER

SCREEN 
ROLLER

SCREEN

DOOR

ACCESS
DOOR

AUDIENCE 
SIDE

SELF-TRIMMING 

FLANGE

3

3

/

8

"

5

3

/

8

"

SUGGESTED CEILING 
INSTALLATION

Optional Accessories:

o

  Extra Drop available to lower picture area 

more than normal. Specify total drop at 

top _____  (black or white) or at bottom 

_____ (black or white). 13' maximum 

total surface height including picture 

area.

o

  No borders (Black masking borders 

standard).

o

  Wireless Remote Control for LVC.

 

o

  Radio Frequency Remote

    

o

  Radio Frequency Range Extender

 

o

  Infrared Remote

o

  Key Locking Cover Plate for 120V Switch 

or LVC.

o

  220/240 Volt (50 Hz) Motor.

o

  Video Projector Interface Control - built-in

o

  SCB-100 RS-232 Serial Control Board - 

built-in 

 

o

  NET-100 Ethernet-Serial Adapter

o

  SCB-200 RS-232 Serial Control Board - 

built-in

 

o

  NET-200 Ethernet-Serial Adapter

 

o

  WC-200 Wall Controller

 

o

  IR-200 Infrared Remote

 Project:

 Architect:
 Phone:
 Contractor:
 Phone:
 Supervisor:
 Phone:
 Supplier:
 Date:
 Revised:

Matte White: 

Horizontal seam required when both dimensions exceed 10'.

High Contrast Matte White:  

Available in sizes where both dimensions do not exceed 10'.

Video Spectra 1.5:  

Available in sizes up to 8' in height.

Silver Lite 2.5:  

Available in sizes up to 8' in height and width.

High Power

®

Horizontal seam required when both dimensions exceed 8'.

WHEN ORDERING, MARK APPROPRIATE SELECTIONS:
Select size from charts on the other side.
Select viewing surface:

o

  Matte White

 

o

  High Contrast Matte White

o

  Video Spectra 1.5  

o

  High Power 

® 

Silver Lite 2.5

 GreenGuard

®

 and GreenGuard

®

 Children and Schools Certified.

Da-Lite

A Milestone AV Technologies Brand

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

P: 574.267.8101 or 800.622.3737

F: 574.267.7804 or 877.325.4832

E: info@da-lite.com

www.da-lite.com

Reviews: