SPECIFICATION DATA
Tensioned LARGe AdvAnTAGe
®
deLuxe eLecTRoL
®
Automatic Electric Projection Screen Model
VIDEO (NTSC 4:3) FORMAT DIMENSIONS
Viewing Area
Nominal Diagonal
Overall Length of Case (does not include flange)
Approx. Ship. Wt.
H x W
Cm
In.
Cm
In.
Cm
Lbs.
Kg
126" x 168"
320 x 427
210"
533
199¼"
506
628
284.9
132" x 176"
335 x 447
220"
559
208¼"
529
655
297.1
144" x 192"
366 x 488
240"
610
225¾"
573
708
321.1
162" x 216"
411 x 549
270"
686
251¼"
638
781
354.3
S
UGGESTED SPECIFICATIONS:
projection screen(s),
(H) x
( W ) . T h e Te n s i o n e d
Advantage
®
Deluxe screen shall have two motors, one to operate door and one to operate screen. Door motor electrically operated 120 volt
(60 Hz) not more than 1.2 amp. Shall have motor mounted inside the roller, to be three wire with ground, quick reversal type, oiled for life,
with automatic thermal overload cutout, integral gears, capacitor and an electric brake to prevent coasting. To have pre-set but adjustable
limit switches to automatically stop fabric door in the ”down“ position. The door will lift to the closed position where a micro switch shall
cut off the electrical current to the door motor. The roller to be of 1.6" diameter aluminum. Screen motor is electrically operated 120 volt (60
Hz) not more than 2.4 amp. Shall have motor mounted inside the roller, to be three wire with ground quick reversal type, oiled for life, with
automatic thermal overload cutout, integral gears, capacitor and an electric brake to prevent coasting. To have pre-set but adjustable limit
switches to automatically stop picture surface in the ”up“ and ”down“ positions. The fabric roller to be of 4½" diameter (5¾" if 270" diagonal,
275" diagonal, or 298" diagonal) metal. Screen fabric to be seamless, flame retardant and mildew resistant vinyl, with black masking borders
standard. Each side of the fabric to have tab guide cable system to maintain even lateral tension and hold surface flat. Custom slat bar with
added weight maintains vertical tension on the screen surface. The ends of the slat to be protected by heavy duty plastic caps enclosing a
preset adjustable mechanism for screen tensioning. Case shall be a white powder coated extruded aluminum. Bottom of case to be self-
trimming with a built-in flange around the bottom of the case. A section of the bottom of the case shall be a retractable aluminum door
that opens and closes automatically with the lowering and raising of the picture surface. The balance of the bottom of the case shall be a
second hinged aluminum door with manual opening to provide access. Hinges shall be mounted in a concealed way. Junction box shall be
internally integrated into the housing making it possible to install the housing and wire to the building’s electrical system during construction.
The junction box shall contain a quick connect connector that is mounted in the housing for easy plug-in connection to the motorized fabric
and roller assembly. The motorized fabric and roller assembly to be installed in the case at the factory or at a later time at the job site. To
be complete with integrated low voltage control unit and three position control switch with cover plate. Suitable for use in environmental
air space in accordance with section 300-22 (c) of the National Electric Code, and sections 2-128, 12-010 (3) and 12-100 of the Canadian
Electrical Code, part 1, CSA C22.1. Screen to be listed by Underwriters’ Laboratories.
All viewing surfaces will be seamless.
All viewing surfaces are standard with black backing except Da-Tex
®
and Dual Vision.
HDTV (16:9) FORMAT DIMENSIONS
Viewing Area
Nominal Diagonal
Overall Length of Case (does not include flange)
Approx. Ship. Wt.
H x W
Cm
In.
Cm
In.
Cm
Lbs.
Kg
108" x 192"
274 x 488
220"
559
220¾"
561
688
312.1
121" x 216"
307 x 549
247"
627
246
1
⁄
2
"
627
764 346.5
135" x 240"
343 x 610
275"
699
272
1
⁄
2
"
693
841 381.5
146" x 260"
371 x 660
298"
757
294¼"
747
870
394.6
SQUARE FORMAT DIMENSIONS
Viewing Area
Overall Length of Case (does not include flange)
Approx. Ship. Wt.
H x W
Cm
In.
Cm
Lbs.
Kg
10'6" x 14'
320 x 427
199¼"
506
628
284.9
14' x 14'
427 x 427
205¾"
523
655
297.1
12' x 16'
366 x 488
225¾"
573
708
321.1
All screens standard with 12" black drop at top, except 270" diagonal, which has 2".
Extra drop may alter case dimensions. Contact Da-Lite for details.
Overall case length dimensions ±¼" (6mm).
Detail dimensional drawings, wiring diagrams and installation instructions available upon request.
Specifications subject to change without notice.
Custom formats and sizes available upon request.
WIDE (16:10) FORMAT DIMENSIONS
Viewing Area
Nominal Diagonal
Overall Length of Case (does not include flange)
Approx. Ship. Wt.
H x W
Cm
In.
Cm
In.
Cm
Lbs.
Kg
110" x 176"
279 x 447
208"
528
205"
521
691
313.4
120" x 192"
305 x 488
226"
574
222
1
⁄
4
"
565
729 330.7
DA-LITE SCREEN COMPANy LLC
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
P 800-622-3737 / 574-267-8101
F 877-325-4832 / 574-267-7804
www.da-lite.com
e-mail: info@da-lite.com
