1.
Determine the desired height of the latch on the gate. Hold the latch in place on
the post and close the gate.
2.
Position the Striker Body “C” on the gate frame by engaging the striker bolt
into the latching tongue. (Check whether the adaptor shim ‘S
3
’ needs to be
applied to fit your gate frame.) When all latch
components are aligned correctly, use the pencil to mark inside the four fixing
slots of the Striker Body “C”.
3.
Place all latch components aside and drill a pilot hole in the center of the
marked slots using a
11
/
64
" (4.5mm) d
rill-bit. Remember that centering the
screws inside the slots allows future adjustment for gate sag.
4.
Secure the Striker Body “C” firmly onto the gate frame using four of the large
hex-head Tek screws supplied.
5.
Open the gate. Place the Latch Assembly back onto the latch post and then close
the gate. Engage the Striker Bolt through the latch tongue again, aligning the main
Latch Body on the latch post so that the Striker Bolt will close in the center of the latch
tongue (the Rivet marks the center of the latching zone).
6.
Hold the Latch Assembly in place and mark the post through the two main screw-
fixing holes at the side of the Round Post Bracket.
INSTALLING THE
ROUND POST BRACKET
Once the “handing” is determined,
insert the Round Post Bracket into
the back of the latch body at a
slight angle, as shown: rotate the
Post Bracket in the direction of
the arrows until it snaps firmly in
alignment on the latch body. Insert
a single short screw (Screw 1) in the
center hole inside the bracket, and
a short screw top and bottom
(screws 2 & 3) of the latch.
Round Post
Bracket
Key
Tongue
FENCE
POST
GATE
FRAME
LATCH
BODY
STRIKER
BODY
Striker
Bolt
Release
Knob
Round Post
Bracket
A
INSTALLATION PROCEDURE
• This latch is designed to be fitted to the “opening” side of the gate. See
notes at right re right- or left-hand installation, and also for the fitting of the
Round Post Bracket (A) to the Latch Body
➧ ➧ ➧
Post sizes: 1
7
/
8
–2", 2
3
/
8
", 2
7
/
8
" (48–51mm, 60mm, 73mm).
Gate frame sizes: 1
3
/
8
" and 1
5
/
8
" (35mm and 41mm).
Gap Variance: 1" -2
1
/
4
" (25mm - 57mm)
Tools: Electric or cordless drill (use low clutch settings), Phillips No.1
screwdriver,
5
/
16
" hex-head (Tek) drill drive (for use in electric/cordless drill),
11
/
64
" [4.5mm] drillbit for pre-drilling metal.
A
B
B
S
1
S
2
C
INSTALLATION NOTES & PROCEDURE
• This latch is designed, ideally, to be fitted to the inside (i.e. house or tennis court side) of the gate. If
installing to the outside (i.e. street side) of the gate ensure there is hand access to operate the latch…or, if
this pack contains an “EXTERNAL ACCESS KIT”, ensure it is fixed to this latch before installing the entire latch
onto the gate (see over for details).
• For 2
3
/
8
" (51mm) fence posts and 1
5
/
8
" (41mm) gate frames, no adapters are required.
This latch kit includes special adapter shims for fitting the latch to posts and gate frames of varying diameters (see S1, S2
& S3). The adapters have the diameter they are designed for molded into them. If required, place two identical adapters
(S1 or S2) into their corresponding positions on the inside the Round Post Bracket facing the Fence Post.
For LokkLatch only installation , follow Step #1
†
STEP #1 — MAIN LATCH BODY
Rivet
S
3
S
1
S
2
Latch Body
Screw 1
Screw 2
Screw 3
7.
Remove the Latch Assembly and drill the pilot holes where marked.
8.
Secure the Latch Assembly using the two remaining hex-head Tek screws supplied.
9.
Check latch operation to ensure smooth, reliable latching. Your LOKKLATCH is now ready for use.
NB:
If this pack does not have an “External Access Kit”, you can purchase one from your supplier.
STEP #2 — EXTERNAL ACCESS KIT
For latch with External Access Kit , follow Step #1, then Step #2
†
For a downloadable Adobe Acrobat (.PDF) version of our Limited LIFETIME WARRANTY,
go to our website at www.ddtechglobal.com
LLINSTR0028PA •instr_LLABRND_1 11 11
(
Note:
Locking the External Access Assembly only locks the Push Button. It does not lock the Latch Body, which is lockable separately.)
RIVET
Horizontal
Locate
Push Rod
into hole
Fixing
Shroud
Push Button
housing
Release
Knob
Release
Knob
Push rod
Large return
Small
return
The External Access Kit (EAK) allows a gate to be
opened and locked from the opposite side to the latch.
The EAK is connected to the Latch Body by a Push Rod.
INSTALLATION PROCEDURE
1.
With the latch in the unlocked position, prop the gate
open. Slide the Release Knob to the up position at the
rear of the Latch Body. Take the Push Rod and, holding
it vertically, slide the Large Return through the slot in the
side of the Latch Body as shown in diagram 1. Be sure the Large Return
protrudes completely through to the other side of the Latch Body.
2.
Lower the Release Knob to the down position so that it encloses the Large
Return of the Push Rod. Turn the key to lock the Release Knob in place.
Rotate the Push Rod to the horizontal position as shown in diagram 2.
3.
To aid with installation, the Push Button is locked. Place the Push Button Assembly
against the opposite side of the Round Post Bracket from the Latch Body.
Place the Small Return of the Push Rod into the hole on the side of the
Push Button as shown in diagrams 3 & 4.
4.
With the Small Return of the Push Rod firmly inside the hole on the Push
Button, slide the Fixing Shroud over the Push Button until the Fixing Shroud
sits firmly into the corresponding Round Post Bracket molding (see diagram 5).
This will leave the Push Rod at a slight angle, which is normal.
5.
Secure the Fixing Shroud to the Round Post Bracket with the four small screws
using the Phillips No. 1 screwdriver. Unlock the Push Button and check for smooth
operation. The External Access Kit is now ready for use.
FOR ROUND POST AND GATE FRAME
®
www.ddtechglobal.com
AUSTRALIA:
Unit 6, 4-6 Aquatic Dr, Frenchs Forest NSW 2086
USA:
7731 Woodwind Drive, Huntington Beach, CA 92647
