background image

Note:
Product specifications may change without notice.
Drawings are indicative only, product appearance may change slightly.
® Davey is a registered trade mark of Davey Products Pty Ltd.
© Davey Products Pty Ltd 2001

HS SERIES MULTISTAGE PUMPS

MODELS:

HS50-05 HS50-06

HS60-06 HS60-08

SERVICING INSTRUCTIONS

SI17/1550/1001

Further information can be found in

Hydrascan

®

 Trouble Shooting Guide (SI10/500/1000)

and X Series Motors (SI05/500/1000) Servicing Instructions

Davey Products Pty Ltd

Member of the GUD Holdings Ltd Group

ABN 18 066 327 517

Head Office and Manufacturing

6 Lakeview Drive,

Scoresby, Australia 3179

Ph:

+61 3 9730 9222

Fax:

+61 3 9753 4100

Website: www.davey.com.au

Customer Service Centre

Ph:

1300 367 866

Fax:

1300 369 119

E-mail: sales@davey.com.au

Interstate Offices

Sydney – Brisbane – Adelaide

Perth - Townsville

International

6 Lakeview Drive,

Scoresby, Australia 3179

Ph:

+61 3 9730 9121

Fax:

+61 3 9753 4248

E-mail: export@davey.com.au

Germany

Kantstrasse 47,

04275 Leipzig

Ph:

+49 341 301 0412

Fax:

+49 341 301 0413

E-mail: DaveyEurop@aol.com

New Zealand

8 Ashfield Street,

Glenfield, Auckland 1310

Ph:

+64 9 444 3622

Fax:

+64 9 444 2179

Website: www.daveynz.co.nz

E-mail: sales@daveynz.co.nz

USA

1005 N. Commons Drive

Aurora, Illinois 60504

Ph:

+1 630 898 6976

Fax:

+1 630 851 7744

Website: www.daveyusa.com

E-mail: sales@daveyusa.com

Summary of Contents for HS Series









Reviews: