background image

 

WeatherLink

®

 for Alarm Output 

Addendum 

 

Introduction 

This Streaming Data Logger is designed to provide an electrical interface 
between a Vantage Pro™ or Vantage Pro2™ weather station console or 
Weather Envoy™ and an electrical device.  You may set a series of 
thresholds for various parameters that will trigger if any of them are met (OR 
condition), all of them are met (AND condition), one and only one is met 
(XOR condition).  You may also test whether a parameter is within (between 
condition) or outside of (not between condition) a certain range, or changing 
at a certain rate (trending), or how far apart (or close) two like parameters are 
from each other.  Finally, you may also test various parameters to see if they 
are reporting a valid number.  This can be used to signal a bad data 
connection or malfunctioning sensor. 
 
This product also contains the functionality of the WeatherLink for Vantage 
Pro Serial version.  Please consult the WeatherLink for Vantage Pro Getting 
Started Guide and on-line Help files for information on the use of the 
WeatherLink program (including its hardware requirements and typical 
installation), package contents, and optional accessories for this product. 
 
If you plan to install this product in a Vantage Pro or Vantage Pro2 console, 
use the notch in the battery door located adjacent to where the PC connector 
protrudes and above the AC power connector to bring out the Connector 
Block wire. 
 
If you plan to install this product in a Weather Envoy, it is recommended that 
you knock out the left-most tab with the Weather Envoy’s PC connector 
facing you and loop the Connector Block wire around the datalogger 
connector to the Weather Envoy and bring it out where this tab was removed. 
 

Hardware Installation and Requirements 

In addition to the requirements for WeatherLink, the Alarm Output capability 
of this product has the following additional hardware requirements. 
 

 

One Free Serial Port or One Free USB port with the Serial to USB 
adapter (Part # 8434) connected to a Windows PC. 

 

Computer running any version of Windows with at least 3 MB free of 
RAM and 512 KB free of hard disk space. 

 

Small Slotted Screwdriver 

1

Summary of Contents for WeatherLink





















Reviews: