background image

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

;;;;;;

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

QQQQQQ

¢¢¢¢¢¢

¢¢¢¢¢¢

¢¢¢¢¢¢

¢¢¢¢¢¢

¢¢¢¢¢¢

¢¢¢¢¢¢

¢¢¢¢¢¢

¢¢¢¢¢¢

¢¢¢¢¢¢

;;;

;;;

;;;

QQQ

QQQ

QQQ

¢¢¢

¢¢¢

¢¢¢

;;;;;;;;;;

;;;;;;;;;;

;;;;;;;;;;

QQQQQQQQQQ

QQQQQQQQQQ

QQQQQQQQQQ

¢¢¢¢¢¢¢¢¢¢

¢¢¢¢¢¢¢¢¢¢

¢¢¢¢¢¢¢¢¢¢

Shown with optional

cabinet mantel,

hearth base, and trim

accessories.

Save this manual for future reference.

WARNING: If the information in this manual is
not followed exactly, a fire or explosion may
result causing property damage, personal in-
jury, or loss of life.

— Do not store or use gasoline or other

flammable vapors and liquids in the vicinity
of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas
supplier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

— Installation and service must be performed

by a qualified installer, service agency, or
the gas supplier.

WARNING: Improper installa-
tion, adjustment, alteration, ser-
vice, or maintenance can cause
injury or property damage. Re-
fer to this manual for correct
installation and operational
procedures. For assistance or
additional information consult
a qualified installer, service
agency, or the gas supplier.

WARNING: This is an unvented
gas-fired heater. It uses air
(oxygen) from the room in
which it is installed. Provisions
for adequate combustion and
ventilation air must be pro-
vided. Refer to 

Air for Com-

bustion and Ventilation sec-
tion on page 4 of this manual.

OWNER’S OPERATION AND INSTALLATION MANUAL

UNVENTED (VENT-FREE)

NATURAL GAS FIREPLACE

VSGF33NR

Remote Ready

Fireplace System

This appliance may be installed in an aftermarket,* permanently located, manufac-
tured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

®

Summary of Contents for Vanguard VSGF33NR





























Reviews: