background image

1

Preface

The PS365XA-HD40 is the hard disk unit (HDD unit) for Pro-face’s PS-3650A/PS-
3710A Series (hereafter referred as the "PS-A") units. This 2.5 inch 40GB hard disk is 
designed to be installed inside the PS-A unit.

Corresponding units: PS-3650A/PS-3651A Series, PS-3710A/PS-3711A Series

• Be sure to check that the PS-A unit’s power is disconnected before installing the unit, in 

order to prevent an electrical shock.

• Do not attempt to modify or open the HDD unit, since it can cause a shock or fire.
• When installing the HDD unit, be sure to read this guide’s “3. Installation” section’s 

information completely to ensure that the unit is correctly installed.

To prevent Accidents

• Since the HDD unit is a precision instrument, be sure it is neither hit by nor pressed 

strongly against another object. After unpacking, be sure the unit is not dropped or 
jolted during installation. Also, a PS-A unit built in to a larger piece of equipment (i.e. 
operation panel) should be removed and packed separately prior to shipping. 

• Be sure water, liquids or metal particles are not allowed to enter the HDD unit. Any of 

these may cause either a breakdown or an electrical shock.

• Do not place or store this unit in a location where there is direct sunlight, excessive 

heat, dust or vibration.

• Do not store or operate the HDD unit near chemicals, or where there are chemical fumes.
• Do not allow anyone other than Pro-face’s own service staff to perform maintenance or 

adjustments to the HDD unit.

• Do not move or shift the PS-A unit while the HDD unit is installed and the PS-A unit's 

power is ON.

• Do not use the HDD unit in locations where corrosive gasses are present, since they 

can lead to a hard disk breakdown.

• To prevent damage to your data, be sure to shut down the PS-A unit's OS before 

turning OFF the main power.

• To prevent hard disk memory leaks, restart the OS periodically.
• A hard disk has a usage lifetime. In order to use your hard disk longer and more stable, 

read through the attachment guide, “Instructions for Using the Hard Disk”.

• In order to extend the lifetime of the hard disk, Pro-face recommends you set the 

Windows

®

 [Control panel]-[Power Management option]-[Turn off hard disks] 

selection to turn the hard disk off when the unit is not being operated. A setting of 5 
minutes is recommended.

Unit Disposal

• When this HDD unit is disposed of, it should be done so according to your country’s 

regulations for similar types of industrial wastes.

Essential Safety Precautions

Summary of Contents for PS365XA-HD40









Reviews: