background image

Parts and Description

The MEGApix Camera is designed to be surface mounted on a wall 

or ceiling. 

RJ-45 Cable

Bracket

Pan/Tilt Stopper Screw

DC Power Cable

Lens

SD Card Slot

Reset Button

67.5 (2.65”)

63.8 (2.51”)

161.7 (6.36”)

76.0 (3.0”)

146.7 (5.77”)

Pressing the reset button on the camera’s control board for five (5) seconds will 

initialize all environmental variables to factory default. Previous setup for IP default, 

time, etcetera will be deleted. If a system IP address is lost, reset the camera back 

to factory default.The following are the default  network settings:

 

IP Mode   

DHCP

 IP Address 

192.168.1.123

 Subnet Mask 

255.255.255.0

 Gateway   

192.168.1.123

 Command Port 

7000

 

HTTP Port 

80

 Live Port   

7001

Resetting the Camera

DWC-MB721M4TIR

DWC-MB721M8TIR

IP 2.1MP Weather Resistant Bullet IR Camera

Mounting the Camera

1. Use the camera’s mounting template or the camera’s housing to mark the 

drilling holes in the mountng surface. 

2. Drill holes into the drywall using the included dry wall anchors. 

3. Pull wires through and make connections. Refer to “

Network Connection

” 

for more information.

Mount the camera to the wall or ceiling using 

the screws provided with the camera. 

4. To adjust the camera’s pan and tilt, 

loosen the Pan/ Tilt stopper screw a little 

before mounting the camera. 

5. Once the camera’s pan and tilt angles 

have been adjusted, tighten the Pan/ 

Tilt stopper screw back to secure the 

camera in its position. 

Prepare the Camera and Mounting Surface 

INSTALLATION

!

Frequent use may cause a System Error

Recommended Settings

Camera Default Color Settings

5

7

 8

Additional Cabling Connections

NETWORK

ENVIRONMENTAL

Frame Rate 

 

 

Up to 30fps at All Resolutions

Video Compression Type 

 

H.264, MPEG4, MJPEG (Super Fine~Low)

IP 

 

 

IPv4, IPv6

Protocol  

 

TCP/IP, HTTP, DHCP, PPPoE, ICMP, ARP, RARP, 

 

 

 

RTSP, NTP, UDP, Multicast

LAN  

 

802.3 Compliance 10/100 LAN

Web Viewer   

 

OS: Windows XP / Vista / 7, MAC OS

 

 

 

Browser: Internet Explorer, Chrome, Firefox, Safari

Video Management Software   

NxMS, DW Spectrum, Pivot

ONVIF Conformance 

 

Yes 

Streaming Capability 

 

Dual-Stream at Different Rates and Resolutions

Power Requirement 

 

DC 12V, PoE (IEEE802.3af Class 2)

Power Consumption 

 

3.5W, 300mA / LED ON: 5W, 430mA

Operating Humidity 

 

Less than 90% (Non-Condensing) 

Operating Temperature/ Humidity 

-10

o

C ~ 50

o

C (14

o

F ~ 122

o

F)

Other Certifications 

 

CE, FCC, RoHS

Memory Slot   

 

24 hours recording to Micro SDHC Card (4GB-32GB)

 

 

 

Card Not Included*

Dimensions  

 

161.7 x 67.5 mm (6.36 X 2.66 in)

Material  

 

Aluminum Housing

Weight  

 

0.93 lbs

Maximum User Access 

                        5 Users

MECHANICAL

ELECTRICAL

Resolution  

 

1920X1080 (16:9) ~ 320X240 (4:3)

IP Rating 

 

 

IP66 (Protects against dust and high pressure water)

LENS

IMAGE

Image Sensor   

                       1/2.8” Sony CMOS Sensor 

Effective Pixels  

 

1920 (H) X 1080 (V)

Minimum Scene Illumination                         F2.0 (30IRE): 2.4 Lux [Color], F2.0 (30IRE): 0.5 Lux [B/W]

Zoom  

 

12x Digitzl Zoom

Lens Type  

 

 

Fixed Lens

Focal Length    

 

4.0mm [DWC-MB721M4TIR]/ 8.0mm [DWC-MB721M8TIR]

Angle of View   

 

Horizontal: 42

o

 Wide Angle

IR Distance 

 

 

50ft Range IR 

Quick Setup Guide

Template Sheet

Before mounting the camera, please check the following: 

1. The mounting surface must be able to sustain five times the weight of your 

camera. 

2. Do not let the cables get caught in improper locations or it can cause 

damage to the cables. 

Thank you for purchasing Digital Watchdog’s MEGApix Weather Resistant Bullet Camera.

Before installing the camera, please verify your model and read this guide carefully.

20140122

The following items are included with a MEGApix Bullet camera 

L-Wrench

IR Bullet Camera

- 12VDC Power

- RJ45 Network

Please refer to the table below for the default camera settings. 

You can reset the camera’s settings to its default color settings by 

pressing the ‘Default’ button at the bottom of the screen. 

Network Connection

There are two options.*

Using a Non-PoE Switch

Using a PoE-Enabled Switch

The MEGApix Camera is PoE-compliant, allowing transmission of power 

and data via a single ethernet cable. Follow the illustrations below to 

connect the camera to a PoE-enabled switch using an ethernet cable. 

If a PoE-enabled switch is not used, use a power adaptor to connect the 

MEGApix Camera to a Non-PoE switch. 

1

2

PREPARATION

TEL: (866) 446-3595

www.Digital-Watchdog.com / technicalsupport@dwcc.tv

Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST

INSTALLATION

Quick Start 

Guide

Mounting 

Template

CD

(Manual & 

Software)

 

2

3

4

 6

Camera Specifications

4 Screws & 4 

Dry Wall 

Anchors

DWC-MB721M4TIR

DWC-MB721M8TIR

IP 2.1MP Weather Resistant Bullet IR Camera

Quick Setup Guide

Reviews: