Division 6 Dual Mini Sequencer Operating Instructions Manual Download | Manualshive

Page: 1 / 14

background image

Dual Mini Sequencer Operating Instructions

Playing Sequences

Push RUN to start playing a sequence. The RUN LED will light to tell you that you are in Run
mode. Push it again to pause. The sequencer steps can be programmed while paused.

Push RESET to stop the sequence, go to step 1, and enter Ready mode. The STEP LED will blink
to let you know that you are in Ready mode. This means that when you press RUN again, the
sequencer will play step 1 on the next clock pulse instead of skipping it and going to step 2.

1
2
3
...
»

Summary of Contents for Dual Mini Sequencer















Reviews:

No comments

Related manuals for Dual Mini Sequencer

Brand: Polyend Pages: 8

e-MIX STUDIO SP-808EX

Brand: Roland Pages: 25

Edirol StudioCanvas SD-80

Brand: Roland Pages: 31

Brand: Audiospektri Pages: 35

Brand: Yamaha Pages: 40

Brand: Yamaha Pages: 158

Brand: Tangible Waves Pages: 2

Brand: Yamaha Pages: 22

Brand: Roland Pages: 10

Brand: Roland Pages: 18

Phase Lab MC-09

Brand: Roland Pages: 21

Brand: Roland Pages: 24

Orchestra M-OC1

Brand: Roland Pages: 38

Brand: Roland Pages: 44

PhraseLab MC-09

Brand: Roland Pages: 88

Sound Canvas SC-50

Brand: Roland Pages: 112

Sound Canvas SC-88 VL

Brand: Roland Pages: 98

Sound Canvas SC-155

Brand: Roland Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands