background image

Dometic Sanitation Corporation

 

328 State Rt. 226, P.O. Box 38, Big Prairie, OH 446 USA 

SeaLand Product Hotline -800-32-9886 (8-5 ET) 

4806

4809, 4848

•   All-ceramic construction

•  Automatic flushing cycle

•  Very low water consumption 

 

(1.5 pints/.7 liter per flush)

•  Push-button operation

•  Full-size seat with elongated opening

•  New flush mechanism reduces noise

VaCuFluSh 4800 SerieS FeaTureS

Water  

Supply

Water hose 

connection

Thread size

1/2 inch MPT

Flow rate at toilet

2 GPM /7.6 LPM

Discharge 

Piping

Hose ID

Standard

1.5 inch/38 mm

Hose runs

Max. horizontal run

50 ft./15 m*

Max. vertical run

6 ft./1.8 m*

electrical 

System

Amp draw

 

(avg.)

12 volts DC

2.0 amps

24 volts DC

1.0 amp

Circuit breaker

12 volts DC

2 amps**

24 volts DC

2 amps**

*

 

See page 8 for further information.

 

**

 

Each toilet must be on separate circuit breaker. Does not include electrical requirements of vacuum pump.

SYSTeM SPeCiFiCaTionS

This manual must be read and understood 

before adjustment, maintenance, or service is 

performed. Modification of this product can 

result in property damage. See page 3.

WarninG

 

iMPorTanT noTiCe

VacuFlush

®

 sanitation systems must 

be installed according to Dometic’s 

 

recommended  procedures. 

 

Do  not  attempt  installation  with

-

out  first  contacting  a  VacuFlush 

 

certified  dealer  or  Dometic  

Corporation.

Sealand

®

VaCuuM ToileT 

oWner’S Manual

VacuFlush

®

 4800 Series Toilets

Summary of Contents for SeaLand VacuFlush 4800 Series

















Reviews: