background image

http://www.tulsawinch.com

SEL-0088-001

                 

REV 1 

July 2020

 

TABLE OF CONTENTS 

SAFETY NOTES ...........................................................................................................................2

 

INTRODUCTION AND THEORY OF OPERATION .........................................................................3

 

HYDRAULIC SCHEMATIC............................................................................................................4

 

MAINTENANCE AND SERVICE ....................................................................................................5

 

WIRE ROPE ................................................................................................................................7

 

DISASSEMBLY ............................................................................................................................8

 

ASSEMBLY ..................................................................................................................................9

 

SERVICING THE MOTOR...........................................................................................................10

 

SERVICING THE BRAKE............................................................................................................11

 

SERVICING THE PLANETARY SET.............................................................................................13

 

TROUBLESHOOTING ................................................................................................................14

 

TORQUE SPECIFICATIONS CHART ...........................................................................................15

 

BILL OF MATERIAL...................................................................................................................16

 

EXPLODED ISOMETRIC ASSEMBLY DRAWING.........................................................................18

 

Summary of Contents for TWG TULSA WINCH 707W



















Reviews: