background image

HDI-03-W 

Mar ‘15 

- 1 -

Contents: 

Page: 

Quick Start 

Safety Precautions 

Preventative Maintenance Schedule 

Unpacking and Inspection 

Compressor Terminology 

Installation – Mechanical 

Lubrication 

Installation – Electrical 

9-10

Start-up Procedures 

11 

Compressor Unit Accessories 

12-14

Compressed Air System Design 

15-16

Refrigerated Air Dryers 

17-18

Compressed Air Filter Assemblies 

19 

Trouble-Shooting Guide 

20-23

DV Systems Limited Warranty 

24-25

Warranty Registration 

26 

Please read this manual before 

installing or using your Air 

Compressor Unit. It contains 

valuable information that will 

help in the receiving, 

installation, use, and 

maintenance of the Unit. 

Please keep this manual in a 

safe place for future reference. 

All of the information, policies, and 

procedures in this reference manual apply 

exclusively to DV Systems. 

Heavy Duty 

Industrial 

(‘HDI’) 

Air Compressor 

Installation, 

Maintenance,  

And 

Service Data 

DV Systems Inc. - Canada 
490 Welham Road 
Barrie, ON 
L4N 8Z4 
Tele: 

(705) 728-5657 

Fax: 

(705) 728-4974 

DV Systems Ltd. - US 
128-B Talbert Road
Mooresville, NC
28117
Tele: 

(704) 799-0046

Fax: 

(704) 799-0355

Web: 

www.dvcompressors.com

 

Email:  sales@dvcompressors.com 

Summary of Contents for HDI



























Reviews: