_______________________________________________________________________________________________________________________________
European Safety Systems Ltd.
Impress House, Mansell Road, Acton, London W3 7QH sales@e-2-s.com Tel: +44 (0)208 743 8880
www.e-2-s.com Fax: +44 (0)208 740 4200
Document No. D209-00-511-IS-SC Issue C 13-06-17 Sheet 1 of 8
INSTRUCTION MANUAL
E2xC1LD2R & E2xC1LD2F Combined Sounder & Beacon
For use in Hazardous Locations
1) Warnings
DO NOT OPEN WHEN AN EXPLOSIVE
ATMOSPHERE IS PRESENT
DO NOT OPEN WHEN ENERGISED
POTENTIAL ELECTROSTATIC CHARGING
HAZARD - CLEAN ONLY WITH A DAMP
CLOTH
HIGH VOLTAGE SHOCK HAZARD. WAIT 5
MINUTES AFTER REMOVING POWER
BEFORE OPENING THE ENCLOSURE
Avertissement:
NE PAS OUVRIR UN PRESENCE
D’ATMOSPHERE EXPLOSIVE
NE PAS OUVRIR ENERGIE
DANGER POTENTIEL CHARGE
ÉLECTROSTATIQUE - NETTOYER
UNIQUEMENT AVEC UN CHIFFON HUMIDE
HAUT TENSION, RISK DE CHOC.
ATTENDEZ 5 MINUTES APRES AVOIR
DEBRANCHE L’ALIMENTATION AVANT
D’OUVRIR LA BOITIER
2) Rating & Marking Information
2.1 ATEX / IECEx certification
The E2xC1LD2 combined alarm horn and LED beacon
complies with the following standards:
EN60079-0:2012+A11:2013 / IEC60079-0: ed. 6.0 (2011-06)
EN60079-15:2010 / IEC60079-15: ed. 4.0 (2010-01)
EN60079-31:2014 / IEC60079-31:2013 ed. 2.0 (2013-11)
Certificate No.
DEMKO 06ATEX 0421554X
IECEx ULD 14.0012X
The E2xC1LD2 combined alarm horn and LED beacon is
rated as follows:
CE Marking
Zones, Gas / Dust Groups and Temperature
Classification
When connected to an approved system the E2XS1 alarm
horn may be installed in:
Zone 2 explosive gas air mixture not likely to occur
in normal operation, and if it does, it will only exist
for a short time.
Zone 22 explosive dust air mixture not likely to occur
in normal operation, and if it does, it will only exist
for a short time.
May be used with gases in groups:
Group IIA
propane
Group IIB
ethylene
Group IIC
hydrogen / acetylene
Having a temperature classification
(for Gas applications) of:
T1
450ºC
T2
300ºC
T3
200ºC
May be used with Dust types:
Group IIIA
combustible flyings
Group IIIB
non-conductive dust
Group IIIC
conductive dust
Maximum Surface Temperature for Dust Applications:
105ºC
90ºC (up to 40ºC ambient only)
Installation must be carried out in compliance with the latest
issue of the following standards:
EN60079-14 / IEC60079-14: Explosive atmospheres -
Electrical installations design, selection and erection
EN60079-10-1 / IEC60079-10-1: Explosive atmospheres -
Classification of areas. Explosive gas atmospheres
EN60079-10-2 / IEC60079-10-2: Explosive atmospheres
–
Classification of areas. Explosive dust atmospheres
E2xC1LD2F
E2xC1LD2R
0518
II 3G Ex nA IIC Gc T3 Ta -20°C to +55°C
II 3D Ex tc IIIC Dc T105°C Ta -20°C to +55°C
II 3D Ex tc IIIC Dc T90°C Ta -20°C to +40C
Summary of Contents for E2 C1LD2F Series
Page 9: ......
