background image

Item #15334

© Copyright 2014 Easthill Group, Inc. 

              Instruction item #15334Q     Rev. 9/14

If you have any questions about the use of this product, please contact 

Eastwood Technical Assistance Service Department: 800.544.5118  >>  email: techelp@eastwood.com

PDF version of this manual is available online  >>  eastwood.com/ 15334manual

The Eastwood Company     263 Shoemaker Road, Pottstown, PA 19464, USA

US and Canada: 800.345.1178     Outside US: 610.718.8335

Fax: 610.323.6268     eastwood.com

5-STAGE 

ELECTRIC 

TURBINE 

HVLP PAINT SYSTEM

INSTRUCTIONS

MAINTENANCE

PAINT GUN 

 

After reassembly after cleaning or periodically with frequent use, apply Gun Lubricant (included) to 
lubricate the Air Valve Stem and Gland Seal to prevent the Needle from sticking 

(Fig W)

.

TURBINE UNIT 

 

The motor has sealed bearings that are pre-lubricated and no internal maintenance is necessary or 
recommended. Clogged Air Intake Filters can cause motor overheating and diminished spray capability. 
Every 50 hours of operation (more often in dirty conditions) the 2 replaceable Air Intake Filters should be 
inspected and cleaned or replaced. 

 

  •  To remove fi lters: Remove Air Filter Housing Acorn Nuts, pull off Air Filter Housings then remove  
   Filters 

(Figs X1 & X2)

. When replacing foam fi lters, align the holes and slide them over the    

    threaded posts fi rst then re-install Housings.

 

  •  When checking fi lters, also inspect the Power Cord and Air Feed Hose for cuts, kinks or any    
    other damage.

STORAGE

 

•  Insert the Air Coupler of the Paint Gun Handle into the Receptacle located on top of the Turbine Unit 
 cabinet

 (Fig Y)

.

 

•  Cover with a plastic trash bag and keep entire unit in a clean, dry environment.

TROUBLESHOOTING

•  Gun produces an uneven spray pattern or fan

-

 Paint or fi lm buildup on Air Cap blocking air holes

      Unplug Turbine Unit and clean buildup from Air Cap

•  Gun “spits” or sputters; discharges large droplets

-

 Paint or fi lm buildup on Needle & Nozzle

      Unplug Turbine Unit and clean buildup from Needle & Nozzle. Note: Use of solvent may be helpful,  

  removal of the Nozzle may be necessary

•  Gun sprays only a small amount of paint or none at all

-

 Clump or piece of paint fi lm blocking paint path

      Unplug Turbine Unit; remove Paint Cup. Remove blockage from paint path of gun then strain paint or  

  coating to remove clumps or fi lm

ACCESSORIES

# 10041Z

 - Eastwood PRE Painting Prep, Aero.  

# 15343

 - 250cc Aluminum Cup w/ Air Feed Tube & Check Valve 

# 29954

 - DeKups Starter Set

# 12846Z

 - Aerosol Injected Cleaner 

# 15344

 - 250cc Aluminum Cup w/ Tefl on Lining, Air Feed Tube & Check Valve 

# 14049

 - Gunner Cup Adapter

# 15335

 - 0.5mm Needle/Nozzle Set 

# 15345

 - 600cc Aluminum Cup w/ Air Feed Tube & Check Valve 

# 11549

 - 3M PPS #2 Adapter

# 15336

 - 0.8mm Needle/Nozzle Set 

# 15346

 - 600cc Aluminum Cup w/ Tefl on Lining, Air Feed Tube & Check Valve 

# 11455 – 11456

 - Respirators

# 15337

 - 1.0mm Needle/Nozzle Set 

# 15347

 - 1000cc Aluminum Cup w/ Air Feed Tube & Check Valve 

# 20403 – 20406

 - Coveralls

# 15338

 - 1.3mm Needle/Nozzle Set 

# 15348

 - 1000cc Aluminum Cup w/ Tefl on Lining, Air Feed Tube & Check Valve 

# 15339

 - 1.5mm Needle/Nozzle Set 

# 15349

 - Replacement Air Inlet Filters (2 Pack)

# 15340

 - 1.8mm Needle/Nozzle Set 

# 50207

 - DeKups #11 Adapter

FIG. X1

FIG. X2

FIG. Y

FIG. W

Gland Nut

Lubricate

Summary of Contents for 15334









Reviews: