background image

IMPORTANT NOTES

1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician

in accordance with current electrical engineering Codes of Practice, Regulations for the Electrical equipment of
Buildings (BS7671), CDM2007 - Construction (Design and Management) Regulations 2007, HSG150 - Health and
Safety in Construction, Statutory requirements and any Specific instruction issued by the Company.

2. After completing the installation and testing of this product it is essential that this leaflet is drawn to the attention of

the person responsible for its future operation and maintenance, and is at all times available for ready reference.

3. These notes assume throughout that the product is disconnected from the supply. It is essential that this is done

before any work is carried out.

4. These Panelboards are only designed for use with Eaton MCCBs. Failure to comply will result in invalid warranty and certification.
5. Operation of the incoming and outgoing devices should only be carried out by an instructed or skilled person.

Memshield 3 630/800A Panelboard/Pan Assemblies
EPBN2863, EPBN21263, EPBN21863, EPBN3880, EPBN31240
EPBPN2863, EPBPN21263, EPBPN21863, EPBPN3880, EPBPN31240

Instruction leaflet LT1210 (

12

/1

9

)

630A MCCB INCOMER FITTING
            EPBKN2633

         EPBKN2634

NOTE: When Top Fed, MCCB terminations must be reversed

800A MCCB INCOMER FITTING
          EPBKN3803

EPBKN3804

Position

on Cover

14Nm

31Nm

31

Nm

46Nm

Position

on Cover

14Nm

31Nm

630A DIRECT CABLE
INCOMER FITTING EPBKN263L
(FOR 630A PANELBOARDS ONLY)

MCCB INCOMING COVER
KNOCKOUT REMOVAL

DO NOT REMOVE FOR DIRECT

CABLE INCOMER

14Nm

Remove for 4 Pole

Bottom Feed Incomer

Remove for 3 Pole

Top and Bottom

Feed Incomer

Remove for

4 Pole Top

Feed Incomer

The use to which this product is put and its place of installation is outside our

 

control.

 

Particular care should therefore be taken to follow the instructions given here and to

 

ensure their continued availability in conjunction with the use of the product.
No responsibility can be accepted by us if these instructions are disregarded.

 

Further 

copies of these instructions and information concerning the installation

 

and proper use 

of this product can be obtained by contacting the:
Technical Services Department
Eaton Electric Limited, 

Middleton

Manchester

M24 1GQ

.

Tel: +44(0)8700 545 333, 
email: ukcommorders@eaton.com

www.eaton.com/recycling

LH OUTGOING CIRCUITS RH OUTGOING CIRCUITS

FED FROM:

INCOMING CABLE SIZE:

INSTALLATION DATE:

CONTRACTOR:

Warning -
Intellectual Property Rights

Eaton wishes to make it clear that it

 

owns intellectual property rights in the

 

product which it manufactures (whether

 

or not listed in this leaflet) and that it will

 

take legal action against any party

 

found to be manufacturing, using, or

 

selling any article which infringes the

 

company’s intellectual property. All

 

marks in this document identified with

 

an R symbol or a TM symbol adjacent

 

to the mark are trademarks of Eaton.

© 20

1

9

 Eaton Electric Limited,

All rights reserved.

BOTTOM FEED

L1

LABEL FITTING

Ensure all way labels are fitted in the correct places

Busbar

Way

Label

TOP FEED

Phase Label

Earth

Labels

Earth

Labels

L1

Cover Way

Labels

Main Switch

Label

Cover Way

Labels

Main Switch

Label

L1

Reviews: