background image

Instruction Manual 

 

Pow-R-Line Retrofit Panelboards 

Page 

1   

 

 

 

Effective: November 2007 

P1R & P2R Retrofit Panels 

                                                        

 

For more information visit: www.EatonCanada.ca                

                                                                      

 

Contents 

INSTALLATION CRITERIA .......................................................................................................................................... 2 

SAFETY MEASURES ..................................................................................................................................................... 3 

PRE-INSTALLATION:  RECEIVING, HANDLING AND STORAGE ......................................................................... 4 

REMOVAL OF EXISTING PANELBOARD INTERIOR .............................................................................................. 4 

INSTALLATION OF RETROFIT PANELBOARD INTERIOR..................................................................................... 4 

ENERGIZING PANELBOARD....................................................................................................................................... 9 

MAINTENANCE ............................................................................................................................................................. 9 

APPENDIX..................................................................................................................................................................... 13 

 

 
 

 

IL01417001E

Summary of Contents for Pow-R-Line P1R Series















Reviews: