background image

CS-4400, CS-5100

01-44C-01

1

INTRODUCTION

We are constantly working on technical

improvement of our products. For this reason,

technical data, equipment and design are

subject  to  change  without  notice.  All

specifications, illustrations and directions in

this SERVICE DATA are based on the latest

products information available at the time of

publication.

ECHO  SERVICE  MANUAL  Ord.401-21

(Model:CS-4200,CS-4400) contains lots of

information for servicing this model.

0

CONTENTS

page

1 SERVICE INFORMATION ............................. 2

1-1 Specification ............................................... 2

1-2 Technical data ............................................ 3

1-3 Torque limits ............................................... 4

1-4 Special repairing materials......................... 5

1-5 Service limits .............................................. 6

1-6 Special tools ............................................... 8

2 EMISSION ADJUSTMENT GUIDE ............... 9

CS-4400

2-1 General adjusting rules .............................. 9

2-2 Presetting idle adjust screw, L mixture needle

and H mixture needle .......................................  9

2-3 Adjusting idle speed and WOT speed ...... 10

CS-5100

2-1 General adjusting rules ............................ 11

2-2 Presetting idle adjust screw, L mixture needle

and H mixture needle .....................................  11

2-3 Adjusting carburettor................................. 12

Reference No.

01-44C-01

R E V I S E D :   2 0 0 5 1 0

INDEX

ISSUED: 200410

Summary of Contents for CS-4400














Reviews: