background image

HCA-2500

15-23C-00

1

lNTRODUCTION

We are constantly working on technical
improvement of our products. For this reason,
technical data, equipment and design are
subject to change without notice. All
specifications, illustrations and directions in
this SERVICE DATA are based on the latest
products information available at the time of
publication.

1

CONTENTS

page

1 SERVICE INFORMATION ............................. 2
1-1 Specification ............................................... 2
1-2 Technical data ............................................ 3
1-3 Torque limits ............................................... 4
1-4 Special repairing materials ........................ 4
1-5 Service limits .............................................. 5
1-6 Special tools ............................................... 6

2 EMISSION ADJUSTMENT GUIDE ............... 7
2-1 General adjusting rules .............................. 7
2-2 Presetting idle adjust screw, L mixture needle
and H mixture needle ........................................ 7
2-3 Adjusting carburettor .................................. 9

Reference No.

 

15-23C-00

I S S U E D :     2 0 0 6 0 6

INDEX

Summary of Contents for HCA-2500











Reviews: