background image

E

ema

X

“SERIES TWELVE” 

ELECTRIC INSTANTANEOUS WATER HEATER

FOR EMERGENCY SAFTEY EQUIPMENT

INSTALLATION AND OWNERS MANUAL 

REQUIRED MANTENANCE

WARNING

BEFORE ATTEMPTING INSTALLATION OF THIS UNIT OR MAKING ANY ADJUSTMENTS

TO THE UNIT ALWAYS BE SURE MAIN CIRCUIT BREAKER IS OFF TO PREVENT DANGER

OF SERIOUS ELECTRIC SHOCK.

MODEL :

SERIAL NO :

INSTALLATION DATE :

ELEMENT RESISTANCE:               OHMS

SWITCH ON FLOW RATE:              GPM

OPERATING TEMPERATURE
MIN:                                MAX:

Eemax Inc., 353 Christian Street, Oxford, CT 06478

1

INSTALLER/ CONSUMER RESPONSIBILITIES

PLEASE TAKE THE TIME TO READ NOT ONLY THIS MANUAL BUT ALSO THE

WARRANTY CARD ENCLOSED. WARRANTY OF THIS HEATER WILL DEPEND ON PROPER

INSTALLATION, OPERATION,  AND REQUIRED MAINTENANCE. THE WARRANTY SHALL BE

VOID IF THE DESIGN ORSTRUCTURE OF THE WATER HEATER HAS BEEN ALTERED IN 

ANY WAY WHATSOEVER. THE MANUFACTURER OF THIS WATER HEATER WILL NOT BE

LIABLE FOR ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION

AND OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES.

IF YOU REQUIRE ANY HELP OR HAVE ANY QUESTIONS RELATING TO THE

INSTALLATION OR PERFORMANCE OF THIS HEATER, PLEASE CALL OUR TECHNICAL

SERVICE DEPARTMENT TOLL-FREE:

1-800-543-6163

HAVE THE INFORMATION LISTED BELOW BEFORE CALLING.

Summary of Contents for ED079480T12EDS











Reviews: