background image

ELECTRIC INSTANTANEOUS WATER HEATER

INSTALLATION GUIDE AND OWNERS MANUAL

IF YOU REQUIRE ANY HELP OR HAVE ANY QUESTIONS RELATING TO THE

INSTALLATION OR PERFORMANCE OF THIS HEATER, PLEASE CALL OUR 
TECHNICAL SERVICE DEPARTMENT TOLLFREE : 1-800-543-6163.
HAVE THE INFORMATION LISTED BELOW BEFORE CALLING :

SERIAL NO.                       MODEL NO. EX             INSTALLATION DATE

EEMAX “SERIES-TWO” WATER HEATERS

MODELS COVERED - EX120 T, TC, T2 - 240/208 V

SPECIAL_________,______V

READ THE GENERAL SAFETY SECTION BEGINNING ON THE INSIDE COVER 

AND THEN THIS ENTIRE MANUAL BEFORE INSTALLING OR OPERATING THIS 
WATER HEATER. IF YOU DON’T FOLLOW THE SAFETY RULES, THE UNIT WILL 
NOT OPERATE PROPERLY AND IT COULD CAUSE DEATH, SERIOUS BODILY 
INJURY AND/OR PROPERTY DAMAGE. READ ALSO THE ENCLOSED 
WARRANTY CARD. WARRANTY OF THIS WATER HEATER WILL DEPEND ON 
PROPER INSTALLATION AND OPERATION. THE WARRANTY SHALL BE VOID IF 
THE DESIGN HAS BEEN ALTERED IN ANY WAY WHATSOEVER. THE 
MANUFACTURER OF THIS HEATER WILL NOT BE LIABLE FOR ANY DAMAGES 
BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION AND 
OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES. 

THE INSTALLATION MUST CONFORM WITH THE INSTRUCTIONS IN THIS

MANUAL; ELECTRIC COMPANY RULES; AND THE LOCAL CODES, OR IN
THE ABSENCE OF LOCAL CODES, WITH THE LATEST EDITION OF THE
NATIONAL ELECTRICAL CODE. THIS PUBLICATION IS AVAILABLE FROM
YOUR LOCAL GOVERNMENT OR PUBLIC LIBRARY OR ELECTRIC COMPANY
OR BY WRITING UNDERWRITERS LABORATORIES, 333 PFINGSTEN ROAD
NORTHBROOK, IL, 60062.

WARNING

1

EX120 Relay.ppt   9/24/2008

Summary of Contents for EX120 T












Reviews: