EemaX EX180 T3 Installation Manual And Owner'S Manual Download

Page: 1 / 9

ema

THREE PHASE THERMOSTATIC

ELECTRIC INSTANTANEOUS WATER HEATER
MODELS: EX240T3, EX240T2T, EX180 T3, EX180T2T

(208 volts only)

INSTALLATION GUIDE AND OWNERS MANUAL

WARNING

BEFORE ATTEMPTING INSTALLATION OF THIS UNIT OR MAKING ANY ADJUSTMENTS
TO THE UNIT ALWAYS BE SURE MAIN CIRCUIT BREAKER IS OFF TO PREVENT DANGER

OF SERIOUS ELECTRIC SHOCK.

INSTALLER/ CONSUMER RESPONSIBILITIES

PLEASE TAKE THE TIME TO READ NOT ONLY THIS MANUAL BUT ALSO THE

WARRANTY CARD ENCLOSED. WARRANTY OF THIS HEATER WILL DEPEND ON PROPER
INSTALLATION AND OPERATION. THE WARRANTY SHALL BE VOID IF THE DESIGN OR

STRUCTURE OF THE WATER HEATER HAS BEEN ALTERED IN ANY WAY WHATSOEVER. THE

MANUFACTURER OF THIS WATER HEATER WILL NOT BE LIABLE FOR ANY DAMAGES
BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION AND OPERATING
INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES.

IF YOU REQUIRE ANY HELP OR HAVE ANY QUESTIONS RELATING TO THE

INSTALLATION OR PERFORMANCE OF THIS HEATER, PLEASE CALL OUR TECHNICAL
SERVICE DEPARTMENT TOLL-FREE:

1-800-543-6163

HAVE THE INFORMATION LISTED BELOW BEFORE BEFORE CALLING.

MODEL :

SERIAL NO :

INSTALLATION DATE :

ELEMENT RESISTANCE:

OHMS

SWITCH ON FLOW RATE:

GPM

OPERATING TEMPERATURE
MIN: MAX:

Eemax Inc., 353 Christian St Oxford, CT 06478

Sold by www.GadgetsGo.com Authorized Dealer

Summary of Contents for EX180 T3










Search results

Summary of Contents for EX180 T3

Reviews:

Related manuals for EX180 T3

Brands by name

Popular brands

EemaX EX180 T3, Installation Manual And Owner'S Manual

Search results

Summary of Contents for EX180 T3

Reviews:

Related manuals for EX180 T3

Brands by name

Popular brands