background image

EemaX Inc., 353 Christian St., Oxford, CT 06478

Tel: 203-267-7890, Fax: 203-267-7975

WARNING

BEFORE ATTEMPTING THE INSTALLATION OF THE UNIT OR 
MAKING ANY ADJUSTMENTS TO THIS UNIT, ALWAYS BE SURE
THAT THE MAIN CIRCUIT BREAKER IS “OFF” TO PREVENT THE
DANGER OF SERIOUS ELECTRIC SHOCK.

FAILURE TO GROUND THE SYSTEM MAY RESULT IN DEATH OR 
SERIOUS INJURY.

BEFORE SWITCHING “ON” THE POWER AT THE MAIN CIRCUIT
BREAKER PANEL, MAKE SURE THAT THE HOT WATER CIRCUIT 
IS FREE OF AIR POCKETS OR PREMATURE FAILURE OF THE
ELEMENT WILL OCCUR.

THREE-PHASE THERMOSTATIC 

DE-IONIZED WATER HEATER

MODELS : EX320TDI, EX240TDI, EX180TDI.         

(480/277 Volts only)

INSTALLATION GUIDE AND OWNERS MANUAL

E

X

ema

TM

PLEASE TAKE THE TIME TO READ NOT ONLY THIS MANUAL BUT
ALSO THE WARRANTY CARD ENCLOSED. WARRANTY OF THIS 
WATER HEATER WILL DEPEND ON CORRECT INSTALLATION AND
OPERATION. . THE WARRANTY SHALL BE VOID IF THE DESIGN OR
STRUCTURE OF THE WATER HEATER HAS BEEN ALTERED IN ANY
WAY  WHATSOEVER. THE MANUFACTURER OF THIS WATER HEATER
WILL NOT BE LIABLE FOR ANY DAMAGES DUE TO FAILURE TO
COMPLY WITH THE INSTALLATION AND OPERATING INSTRUCTIONS
OUTLINED ON THE FOLLOWING PAGES.

IF YOU REQUIRE ANY HELP OR HAVE ANY QUESTIONS RELATING
TO THE INSTALLATION OR PERFORMANCE OF THIS HEATER, PLEASE
CALL OUR  TECHNICAL SERVICE  DEPARTMENT TOLL-FREE AT:

1-800-543-6163

INSTALLER / CONSUMER RESPONSIBILITIES

Summary of Contents for EX180TDI










Reviews: