background image

1

36" GAS RANGE INSTALLATION INSTRUCTIONS

 If the information in this manual is not followed exactly, a fire 

or explosion may result causing property damage, personal injury or death.
FOR YOUR SAFETY:

—  Do not store or use gasoline or other flammable vapors and liquids in  

the vicinity of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS:

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not use any phone in your 

building.

•  Immediately call your gas supplier from a neighbor's phone. Follow the 

gas supplier's instructions.

•  If you cannot reach your gas supplier, call the fire department.

—  Installation and service must be performed by a qualified installer, 

service agency or the gas supplier.

 

P/N 318201779 (1006) Rev. A

English - pages 1-8; Español - páginas 9-16

Notes - pages 17-19; Wiring Diagram - page 20

Note: Wiring diagram for this model is enclosed in this booklet (see page 20).

Printed in United States

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

OBSERVE ALL GOVERNING CODES AND ORDINANCES.

Note: 

For 

appliances 
installed in 
the state of 
Massachusetts 
see page 2.

Refer to your 

serial plate for 

applicable 

agency 

certification

NOTE:

 28" (71.1 cm) minimum clearance between the 

cooktop and the bottom of the cabinet when the bottom 
of wood or metal cabinet is protected by not less than 
1/4" (0.64 cm) flame retardant millboard covered with 
not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) 
stainless steel, 0.024" (0.6 mm) aluminum, or 0.020" 
(0.5 mm) copper.

34" (86.4 cm) minimum clearance when the cabinet 
is unprotected.

Do not pinch the power supply cord between the range 
and the wall.
Do not seal the range to the side cabinets.

A

B

C

D

E

G

F

13" Max.

(33 cm Max.)

24" Min.

(61 cm Min.)

24 1/2" Max.

(62.2 cm Max.)

35 7/8" Min.

(91.1 cm Min.)

See

note

Grounded

Wall Outlet 

location

WALL

W

ALL

If there is a wall:

7" Min.

(17.8 cm Min)

Left side

18" Min.

(45.7 cm Min.)

If there is a wall:

7" Min.

(17.8 cm Min.)
Right side

A. HEIGHT

B. WIDTH

C. DEPTH TO 

FRONT OF RANGE

D. HEIGHT OF 

COOKTOP

E. DEPTH WITH 

DOOR OPEN

F. HEIGHT OF 

COUNTERTOP

G. MINIMUM 

CUTOUT WIDTH

41 5/8" (105.7 cm) Min.

42 5/8" (108.3 cm) Max.

35 7/8"

(91.1 cm)

27 ½"

(69.9 cm)

35 3/4" (90.8 cm) Min.  

36 3/4" (93.3 cm) Max.

47 3/8"

(120.3 cm)

36" (91.4 cm) Standard

35 3/4" (90.8 cm) Min.

36 1/16"

 (91.6 cm)

Summary of Contents for ICON Professional E36GF76JPS





















Reviews: