83923
/ EN2212
Technical Specifications
Safety and environmental conditions
CE marking
LV directive 2014/35/EU
RoHS directive (EU) 2015/863
Standard
EN 61010:2010/A1:2019*
EN 60947-7-3-2009**
WEEE directive 2012/19/EU
* Maximum temperature of the busbar: 120ºC (Sum of the busbar temperature rise and the
ambient temperature)
** Only applicable to article number 500040
The UAK is only suitable for busbar. This product is designed
to be safe under the following conditions:
Specifications
Environmental conditions
Standard:
Class:
Operating temperature:
Relative humidity:
Operating height:
Protection degree:
Pollution degree:
Measurement category:
IEC 60721-3-3:1996
3K3
+5°C - +40°C
5% - 85%, non condensing
0..2000m over NN
IP20
2
CAT III
Application conditions
Primary:
Umax:
Test voltage:
Impulse voltage:
Imax:
Voltage drop:
Fuse (UAK4Z):
Secondary lead:
Torque:
Busbar
690Vac
3kV / 50Hz
6kV 1,2 / 50µs
2A
<500mVac
5x25mm (with indicator)
10A SIBA DIN41576-2
1mm² flexible, 50cm, end-sleeve
1.5 – 2.0Nm
Storage
Temperature:
Relative humidity:
Material:
-20°C - +70°C
5% - 85%, non condensing
PA 6.6, UL94 V2
Specifications per type
UAK4Z
UAK16
UAK16N
With fuse
Yes
No
No
Weight (gr)
160
160
160
Connection
1,5-4mm
2
0,1-16mm
2
0,1-16mm
2
Colour
Black
Black
Blue
ELEQ reserves the right to carry out modifications on its products, in
order to improve them, without prior notice.
Safety instruction
All activities for installation, commissioning and maintenance
of this voltage tap must be performed by qualified personnel
that have the knowledge of applicable safety precautions.
This guide assumes that the reader of this document has
sufficient electro-technical knowledge to understand the
content of this document.
General
The UAK is a voltage tap for busbar and can only be used
measuring electrical voltages. The UAK is suitable for
measurement purposes only. The UAK should be mounted on
the primary conductors in a weather protected and dry
location.
Explanation of symbols
This product is designed according to the
EN-IEC 61010-1:2010 standards and therefore this
product meets the requirements of the Low Voltage
Directive 2014/35/EU.
Read the installation guide before mounting the
product. Unprofessional work activities on electrical
installations may result in a threat of danger to the life
and health of human beings and livestock!
RoHS Directive (EU) 2015/863
ELEQ states that they only uses qualified component
in their products from manufacturers, whose
specifications meet or exceed the requirements of
the European Directive for the Restriction of use of
certain Hazardous Substances.
WEEE Directive 2012/19/EU
The 'crossed out wheeled bin' symbol indicates that
the equipment should not be disposed as unsorted
municipal waste. Contact a qualified recycler for
disposal.
UAK (Fused) Voltage Tap
Installation Guide
UAK4Z
(Fused phase, 500040)
UAK16
(Phase, 500041)
UAK16N
(Neutral, 500042)
Read this installation guide before installing the product
83923
/ EN2212
Technical Specifications
Safety and environmental conditions
CE marking
LV directive 2014/35/EU
RoHS directive (EU) 2015/863
Standard
EN 61010:2010/A1:2019*
EN 60947-7-3-2009**
WEEE directive 2012/19/EU
* Maximum temperature of the busbar: 120ºC (Sum of the busbar temperature rise and the
ambient temperature)
** Only applicable to article number 500040
The UAK is only suitable for busbar. This product is designed
to be safe under the following conditions:
Specifications
Environmental conditions
Standard:
Class:
Operating temperature:
Relative humidity:
Operating height:
Protection degree:
Pollution degree:
Measurement category:
IEC 60721-3-3:1996
3K3
+5°C - +40°C
5% - 85%, non condensing
0..2000m over NN
IP20
2
CAT III
Application conditions
Primary:
Umax:
Test voltage:
Impulse voltage:
Imax:
Voltage drop:
Fuse (UAK4Z):
Secondary lead:
Torque:
Busbar
690Vac
3kV / 50Hz
6kV 1,2 / 50µs
2A
<500mVac
5x25mm (with indicator)
10A SIBA DIN41576-2
1mm² flexible, 50cm, end-sleeve
1.5 – 2.0Nm
Storage
Temperature:
Relative humidity:
Material:
-20°C - +70°C
5% - 85%, non condensing
PA 6.6, UL94 V2
Specifications per type
UAK4Z
UAK16
UAK16N
With fuse
Yes
No
No
Weight (gr)
160
160
160
Connection
1,5-4mm
2
0,1-16mm
2
0,1-16mm
2
Colour
Black
Black
Blue
ELEQ reserves the right to carry out modifications on its products, in
order to improve them, without prior notice.
Safety instruction
All activities for installation, commissioning and maintenance
of this voltage tap must be performed by qualified personnel
that have the knowledge of applicable safety precautions.
This guide assumes that the reader of this document has
sufficient electro-technical knowledge to understand the
content of this document.
General
The UAK is a voltage tap for busbar and can only be used
measuring electrical voltages. The UAK is suitable for
measurement purposes only. The UAK should be mounted on
the primary conductors in a weather protected and dry
location.
Explanation of symbols
This product is designed according to the
EN-IEC 61010-1:2010 standards and therefore this
product meets the requirements of the Low Voltage
Directive 2014/35/EU.
Read the installation guide before mounting the
product. Unprofessional work activities on electrical
installations may result in a threat of danger to the life
and health of human beings and livestock!
RoHS Directive (EU) 2015/863
ELEQ states that they only uses qualified component
in their products from manufacturers, whose
specifications meet or exceed the requirements of
the European Directive for the Restriction of use of
certain Hazardous Substances.
WEEE Directive 2012/19/EU
The 'crossed out wheeled bin' symbol indicates that
the equipment should not be disposed as unsorted
municipal waste. Contact a qualified recycler for
disposal.
UAK (Fused) Voltage Tap
Installation Guide
UAK4Z
(Fused phase, 500040)
UAK16
(Phase, 500041)
UAK16N
(Neutral, 500042)
Read this installation guide before installing the product
83923
/ EN2212
Technical Specifications
Safety and environmental conditions
CE marking
LV directive 2014/35/EU
RoHS directive (EU) 2015/863
Standard
EN 61010:2010/A1:2019*
EN 60947-7-3-2009**
WEEE directive 2012/19/EU
* Maximum temperature of the busbar: 120ºC (Sum of the busbar temperature rise and the
ambient temperature)
** Only applicable to article number 500040
The UAK is only suitable for busbar. This product is designed
to be safe under the following conditions:
Specifications
Environmental conditions
Standard:
Class:
Operating temperature:
Relative humidity:
Operating height:
Protection degree:
Pollution degree:
Measurement category:
IEC 60721-3-3:1996
3K3
+5°C - +40°C
5% - 85%, non condensing
0..2000m over NN
IP20
2
CAT III
Application conditions
Primary:
Umax:
Test voltage:
Impulse voltage:
Imax:
Voltage drop:
Fuse (UAK4Z):
Secondary lead:
Torque:
Busbar
690Vac
3kV / 50Hz
6kV 1,2 / 50µs
2A
<500mVac
5x25mm (with indicator)
10A SIBA DIN41576-2
1mm² flexible, 50cm, end-sleeve
1.5 – 2.0Nm
Storage
Temperature:
Relative humidity:
Material:
-20°C - +70°C
5% - 85%, non condensing
PA 6.6, UL94 V2
Specifications per type
UAK4Z
UAK16
UAK16N
With fuse
Yes
No
No
Weight (gr)
160
160
160
Connection
1,5-4mm
2
0,1-16mm
2
0,1-16mm
2
Colour
Black
Black
Blue
ELEQ reserves the right to carry out modifications on its products, in
order to improve them, without prior notice.
Safety instruction
All activities for installation, commissioning and maintenance
of this voltage tap must be performed by qualified personnel
that have the knowledge of applicable safety precautions.
This guide assumes that the reader of this document has
sufficient electro-technical knowledge to understand the
content of this document.
General
The UAK is a voltage tap for busbar and can only be used
measuring electrical voltages. The UAK is suitable for
measurement purposes only. The UAK should be mounted on
the primary conductors in a weather protected and dry
location.
Explanation of symbols
This product is designed according to the
EN-IEC 61010-1:2010 standards and therefore this
product meets the requirements of the Low Voltage
Directive 2014/35/EU.
Read the installation guide before mounting the
product. Unprofessional work activities on electrical
installations may result in a threat of danger to the life
and health of human beings and livestock!
RoHS Directive (EU) 2015/863
ELEQ states that they only uses qualified component
in their products from manufacturers, whose
specifications meet or exceed the requirements of
the European Directive for the Restriction of use of
certain Hazardous Substances.
WEEE Directive 2012/19/EU
The 'crossed out wheeled bin' symbol indicates that
the equipment should not be disposed as unsorted
municipal waste. Contact a qualified recycler for
disposal.
UAK (Fused) Voltage Tap
Installation Guide
UAK4Z
(Fused phase, 500040)
UAK16
(Phase, 500041)
UAK16N
(Neutral, 500042)
Read this installation guide before installing the product
83923 / EN2212
ELEQ b.v.
Tukseweg 130, 8331 LH Steenwijk, The Netherlands
+31 (0) 521 533 333 info@eleq.com www.eleq.com
ELEQ b.v.
Tukseweg 130, 8331 LH Steenwijk, The Netherlands
+31 (0) 521 533 333 info@eleq.com www.eleq.com
2014/35/EU.
