Mounting and setting instructions
elero folding shutter drive type KL/DMA
General information
Torque switch-off
The drive incorporates an electronic torque switch-off.
The torque at which it switches off can be adjusted over a continuous
range by turning the "T" knob on the circuit board. The torque is
increased by turning in the + direction, and reduced by turning in the
- direction. The factory setting (in the centre) corresponds to the
standard value that suits most cases. After three uninterrupted travel
operations between the stops (opening and closing) the travel is
programmed. The device will automatically learn the end shut-of
points after driving against the stops for the first time. After this,
the drive will automatically switch to a soft switch-off shortly before
reaching the stops.
It is still, however, necessary to have the stops. It is not possible to
operate the drive without fixed stops.
Resetting
It is possible to reset the end shut-of points and/or the soft switch-off
after the system has learnt them.
Important:
It is only necessary to reset the drive if structural changes
are made to the track.
Reset procedure
1. Connect the OPEN and CLOSE direction lines to a switch.
2. Close the switch for at least 10 seconds.
3. Reconnect the device for operation.
(See connection example.)
Important:
Both drives in a pair can be reset simultaneously by
connecting them in parallel.
Shut-off torque: 15 Nm–25 Nm, over a continuous range.
1 drive is required for each leaf. The electronics permit
multiple drives to be connected together. (Observe the
maximum rating of the power supply.)
Functional description of the rotary start-up delay knob:
1. Folding shutters without rebate profile
Adjusting the rotary knob when folding shutters
without a rebate profile are used.
2. Folding shutters with rebate profile
Range of adjustment for folding
shutter leaves with rebate profile
Range of adjustment for folding
shutter leaves without rebate profile
Adjusting the start-up delay
The drive operates without delay under the factory setting (rotary
knob in the centre position).
If a rebate profile is fitted to one of the two wings, the rotary "L-R"
knob can be adjusted for a start-up delay for left or right handed
running.
Delay: 0–20 seconds, continuous range
Technical data
Voltage:
230 V
Power:
160 W
Frequency:
50 Hz
Torque:
20 Nm
Current consumption:0,7 A
Short period operation: 4 mim
Only for internal
connections
0-R = start-up delay for right-running
0-L = start-up delay for left-running
(View of the shaft through the drive)
N
W8
W1
N
PE
W10
W9
PE
LC
L
R
W5
W4
W2
W6
W3
RC
W7
L
0
R
K2
L
R
K1
-
+
T
Start-up delay
Adjustment of the:
Torque switch-off
Connection example
KL/DMA 1 folding
shutter drive
KL/DMA 2 folding
shutter drive
Mains
Extension of control is possible,
see elero-control system documentation.
Shutter
switch
After lifting off the
two rear covers
(see front
illustration) the
circuit board
becomes visible
as follows.
Example of connecting two folding shutters on one window
0
L
R
L
R
0
0 seconds
20 seconds
Range of
adjustment
L
0
R
0 seconds
20 seconds
Range of
adjustment
L
R
0
L
0
R
Folding shutters without rebate profile
Left motor
circuit board
Right motor
circuit board
L
R
0
L
0
R
Left motor
circuit
board
Right motor
circuit
board
Left-hand leaf
with rebate profile
Right-hand leaf
with rebate profile
0
Left
motor
circuit
L
0
R
L
Right motor
circuit
board
R
Outer side
Figure 2
The continuously adjustable delay also makes it possible to implement
overlapping opened shutters (see Figure 3).
Overlap
left leaf
right leaf
Outer side
1 = on
2 = off
Figure 3
Z
Figure 1
Important!
It is important that both drives are adjusted in
accordance with Figure 2. The leaf that does not
have the rebate profile also requires a start-up delay.
Operating
point
L
N
PE
Capacitor
Capacitor
Electronics
Electronics
Winding
thermostat
Winding
thermostat
Mains 230V/50Hz
Switch box
20
16 802.1901
We reserve the right to make technical changes 03/06
20
20
20
20
20
20
elero UK Ltd.
Foundry Lane – Halebank
Widnes, Cheshire WA8 8TZ
Tel. (44) 870/2 40 42 19
Fax (44) 870/2 40 40 86
sales@elerouk.co.uk
www.elero.com
