PO Box 100 • Hildebran, NC 28637 USA • 828-397-4200 Voice • 828-397-4415 Fax
http://www.elkproducts.com • email: info@elkproducts.com
LCD Keypad
ELK-M1KP
FEATURES
!
Large, Easy to Read Characters
!
Back lighted with Adjustable Intensity
!
Removable Hinged Door
!
Programmable Function Keys (6)
!
Unique Menu Navigation/Direction Keys
!
Operates on 4-Wires (M1 Data Bus)
!
Adjustable Beep Tone and Volume
!
Accepts Plug-in Proximity Card Reader (Optional)
!
Input for 1 Supervised Zone
!
One Programmable Voltage Output
!
Exit, Stay, Chime, and Bypass Keys
SPECIFICATIONS
!
Input Connection: 6 Pin Plug-in "Flying Lead" Connector Included
!
Prox Connection: 5 Pin Plug-in "Flying Lead" Connector (optional ELK-WO35A required for external prox reader)
!
Color: Glacier White
!
Operating Voltage: 13.8 VDC
!
Current Draw: 40 - 50 mA Idle (low back light level, sounder silent)
160 mA Fully Active (max. back light & sounder active)
!
Size: 6.875" W x 5.25" H x 1.375 D
Features and Specifications subject to change without notice.
L526 10/05
APPLICATION
The ELK-M1KP is an addressable LCD Keypad for the M1 Cross
Platform Controls. It features a 32 character back lighted display with
adjustable intensity and extra large character fonts for ease of readabil-
ity. The M1KP includes a plug-in connector on the back for adding an
internal proximity reader (ELK-M1PR) or for interfacing to virtually any
external 26 bit Wiegand compatible proximity reader. Prox cards/fobs
can be used for touchless arming, disarming, door strike control, etc.
ELK-M1KP
1
See Note about
Data Bus
Termination
6
BLACK
WHITE
GREEN
RED
Keypad
Wiring
Assembly
Data Bus Cable
CAT5 or CAT6 Recommended
Optional programmable Zone Input from Keypad
Hookup Diagram for Keypad
(see M1 Instruction Manual and back of this sheet for multiple Keypad hookups.)
Splice 6 Pin Keypad Wiring Assembly to the Data Bus cable using ELK-900-2 "B" Connectors.
BROWN
Optional programmable Output from Keypad
Keypad 1
The optional Zone Input # or Output # is
determined by the Keypad Address.
Load (50mA max)
I.E. LED, Relay
-
+
To BLACK (Neg) Wire
To BROWN Wire
N.C. N.O.
2200
Ohm
EOL
To BLACK (Neg) Wire
BLUE
To BLUE Wire
NOTE: The first batch of M1KP Keypads provided a switched
negative (pull to ground) output. Connect per diagram above.
These units have the letter "E" at the end of the ID number on
the lower back side of the board. EG: PC096
E
Boards with a
letter "F" or later provide the output as a switched positive.
Load (50mA max)
i.e. Relay, LED
-
+
To Red (Pos) Wire
To Brown Wire
KP Zone Output
Address # #
1 193 193
2 194 194
3 195 195
4 196 196
5 197 197
6 198 198
7 199 199
8 200 200
KP Zone Output
Address # #
9 201 201
10 202 202
11 203 203
12 204 204
13 205 205
14 206 206
15 207 207
16 208 208
