background image

02-5/2018 Rev.0

RFPM-2M

Made in Czech Republic

1/7

60 - 90 %

80 - 95 %

20 - 60 %

0 - 10 %

80- 90 %

RF

RP

-2

0

PULS 1

PULS 2

S0+

S0-

TARIF

TARIF

router

1

2

3

4

5

6

7

8

10

11

12

13

9

15

7

14

STORAGE

ELKO EP, s.r.o. | Palackého 493 | 769 01 Holešov, Všetuly | Czech republic | e-mail: elko@elkoep.com

EN

 Support: +420 778 427 366 

 www.elkoep.com

Energy gateway

EN

Charakteristika 

• 

The energy gateway is a central device for assessing energy consumption (electricity, water, gas).

• 

• It acts as an interface between the pulse converter RFTM-1 and your smartphone.The Energy 
Gateway allows you to connect up to 8 pulse transducers.

• 

Connection to the data network is made by means of LAN Ethernet connector or wirelessly via a 
Wi-Fi network.

• 

The monitored data is stored inside the unit (it can also be sent to  external storage - cloud).

• 

By means of the application iHC and cloud connection, it is possible to maintain online access to 
data and monitoring history.

• 

Up to 4 tariff meter readings of electricity consumption, which can be displayed in the form of kWh 
or financial costs.

• 

Option of setting reaction to specific consumption to switch the output on or off (RFSA-6x and 
CU3).

• 

The unit enables connecting up to three current transformers CT50 to each other for measuring 
electricity.

• 

Direct connection to iNELS BUS using integrated CIB terminals.

• 

3-module design, mounted on a DIN rail into the switchboard.

• 

The supply includes an internal antenna AN-I, if the unit is installed in a metal switchboard, you can 
use the external antenna AN-E to enhance the signal.

• 

The device supply voltage is provided from monitored phases.

• 

Range up to 100 m (in open space), if the signal between the controller and the user is weak, use 
the signal repeater RFRP-20 or protocol component RFIO

2

 that support this feature.

• 

Communication frequency with bidirectional protocol iNELS RF Control.

• 

In order to communicate with the gateway, it must be connected to the local network using the 
RJ45 Ethernet connector or wirelessly over the WiFi network.

• 

The Energy Gateway stores the measured data directly on the internal memory storage. Online 
data and history can be viewed through iHC applications (MAIRF and MIIRF) or cloud connections 
on the ELKO Cloud site. The last option is to display the measured values directly on the RFPM-2 
web interface.

• 

Measurement of power consumption can be distinguished by up to four tariffs that can be 
displayed in kWh or financial costs.

• 

Other benefits include the ability to set the response to a specific consumption. An example may 
be to switch off or on the RFSA - 6x and CU3 outputs.

• 

The energy gate takes usually 10 minutes, but not more than 1 hour.

Assembly 

mounting into switchboard

Connection 

connection to the tariff 

(potential free contact)
CAUTION! Do not connect the HDO contact)

Description, Indication

1. Terminals for connection of current 

measuring probes

2. Connect Ethernet
3. Storage operation indication
4. WiFi antenna
5. Relay switch indication
6. RESET button:

- Enter the bootloader - turn off  the power, 

press the button and hold the button> 2s 
when the power is on

- Return to factory settings - power off , press 

button and hold power button> 10s

7. Voltage and voltage terminals
8. Relay output
9. Supply voltage indication / unit status:

- Lit - STOP status
- Flashes - RUN status

10. Pulse and tariff  inputs

11. RF communication indication
12. RF antenna
13. Tariff  indication:

- TARIFF 1: red
- TARIFF 2: green
- TARIFF 3: blue
- TARIFF 4: Yellow

14. RF, LAN and WLAN addresses
15. Phase status indication L1, L2, L3:

- Failure (redundancy): red
- Phase active: green
- Unmonitored phase: LED off 

Radio frequency signal penetration through various construction materials 

brick walls

wooden structures 

with plaster boards

reinforced 

concrete

metal partitions

common glass

Summary of Contents for RFPM-2M








Reviews: