background image

R-5210

Page 1

WARNING:  If the information in
this manual is not followed exactly, a
fire or explosion may result causing
property damage, personal injury or
loss of life.

 — Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

 — WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch;
do not use any phone in your
building.

Immediately call your gas supplier
from a neighbor's phone.  Follow
the gas supplier's instructions.

If you cannot reach your gas
supplier, call the fire department.

 — Installation and service must be

performed by a qualified installer,
service agency or the gas supplier.

INSTALLATION  INSTRUCTIONS

AND

OWNER'S  MANUAL

UNVENTED

ROOM HEATER

MODELS

SR-10T-2
SR-18T-2
SR-30T-2

EFFECTIVE DATE

MARCH, 2000

This is an unvented gas-fired heater.  It
uses air (oxygen) from the room in which
it is installed. Provisions for adequate com-
bustion and ventilation air must be pro-
vided. Refer to page 4.

WARNING: If not installed, operated and
maintained in accordance with the manu-
facturer's instructions, this product could
expose you to substances in fuel or from
fuel combustion which can cause death or
serious illness.

WATER VAPOR:  A BY-PRODUCT OF
UNVENTED ROOM HEATERS
Water vapor is a by-product of gas
combustion. An unvented room heater
produces approximately one (1) ounce
(30ml) of water for every 1,000 BTU's
(.3KW's) of gas input per hour. Refer to
page 4.

SR-30T SHOWN

Summary of Contents for SR-10T-2



















Reviews: