ENDA ATM9321
ANALOG TIMER with DIGITAL DISPLAY
Control output state LED
(Light is on when control output is energized)
1. /2 ATM9321-E-09050219
Set key
Timer setting knob
Timer display
(minute)
Plastic injection presses, automatic bread making ovens, nylon bag machines,
shrink packing machines, furniture presses, industrial ovens, textile machines,
ironing presses and other time control applications.
Application Areas
Technical Specifications
Thank you for choosing ENDA ATM9321 analog timer.
Read this document carefully before using this device. The guarantee will be
expired by damaging of the device if you don't attend to the directions in the user
manual. Also we don't accept any compensations for personal injury, material
damage or capital disadvantages.
* 96 x 96mm sized.
* Digital display for timer value.
* Selectable scale with 0 ... 9.99 or 0 ... 99.9 or 0 ... 999 minutes
* Selectable mode A (on-delay) and mode B
(off-delay) output functions.
* Start by start input.
* Reset by reset input.
* Easy setting procedure.
* Having CE mark according to European Norms.
ELECTRICAL CHARACTERISTICS
Supply voltage
24V AC %10, 50/60Hz or optinal
230V AC +%10 -%20, 50/60Hz or
9-30V DC SMPS module.
±
Power consumption
Max. 6VA
2.5mm²'lik screw-terminal connections.
0 ... 9.99 or 0 ... 99.9 or 0 ... 999 minutes (selectable)
±
1 digit
±
±
%4 for analog scale, %0,5 for timer display (of full scale)
3 digits, 7.62mm, 7 segment red LED
Wiring
Scale
Sensitivity
Accuracy
Display
Data Retention
EMC
Safety requirements
EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B is satisfied for EMC tests.
EEPROM (Min. 10 years)
EN 61010-1: 2001 (Pollution degree 2, overvoltage category II)
Contact input (during min. 5ms.)
Contact input
HOUSING
Housing type
Suitable for flush-panel mounting.
Dimensions
W96xH96xD50mm
Weight
Approx. 250g (after packing the device)
Enclosure material
Self extinguishing plastics
CONTROL
Mode A : Control output is energized after setting time is over
Mode B : Control output is energized during setting time.
.
Output function
A/D converter
10 bits
OUTPUTS
Control output
Relay : 250V AC, 2A (for resistive load), NO+NC or 12V DC 20mA logic output
Mechanical 30.000.000 operation; electrical 300.000 operation.
Life expectancy for relay
ENVIRONMENTAL CONDITIONS
Height
Max. 2000m
80%, up to 31°C decreasing linearly 50% at 40°C
Ambient/storage temperature
Max. relative humidity
0 ... +50°C/-25 ... 70°C
Rated pollution degree
According to EN 60529 Front panel : IP60
Rear panel : IP20
Dimensions
50mm
14mm
57mm
99mm
Flush mounting
clamp
Depth
Rubber
packing
Panel
Panel cut-out
105mm
90.5mm
Do not use the device in locations subject to corrosive and flammable gasses.
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
For removing mounting clamps:
Push out the flush-mounting clamp in direction
1.
Then, pull out the clamp in direction
2.
1
2
INPUTS
Start input
Reset input
Setting value is
percentage of
the full scale.
50
10
0
ENDA
OUT
20
30
40
min
100
%
ATM9321
SET
90
80
70
60
50
10
0
ENDA
OUT
20
30
40
min
100
%
ATM9321
SET
90
80
70
60
1) Panel thickness should be
max. 10mm.
2) If there is no 60mm free
space at the back side of the
device, it would be difficult to
remove it from the panel.
Note :
english