INSTALLATION NSTRUCTIONS
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase.
Original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims
must be verified and approved by Enerwave, Inc. Warranties from other Enerwave products may vary. This warranty
is nontransferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from
misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the
applicable state law, Enerwave shall not be liable to the purchaser or end user customer of Enerwave products for
direct, indirect, incidental, or consequential damages even if Enerwave has been advised of the possibility of such
damages. Enerwave’ total liability under this or any other warranty, express or implied, is limited to repair,
replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or
any other legal theory.
© 2016 Enerwave Home Automation
●
WWW.ENERWAVEAUTOMATION.COM
●
CA, USA
0210160033-0
6
Model: ZW15SM-PLUS
Wireless Home Automation Control
ON/OFF Switch
with Smart Meter
WARNING:
Turn the POWER OFF at the circuit breaker before installing the Switch
Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a qualified electrician performs this installation. Make sure to turn off the circuit breaker or fuse(s) and make
sure power is off before wiring the device. Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance so an unintentional activation may occur if the wrong button on the remote is pressed. Z-
Wave devices can be automatically powered on by programmed events. Unattended or unintentional operation could result in hazardous conditions. Z-Wave enabled devices should never be used to supply power to, control or monitor medical and/or life support equipment.
To enable the 3-way
function install the ZW3K-N in conjunction with the ZW15SM-PLUS. For use with incandescent, halogen, and CFL lights. Use copper wires only.
•
Connect the BLACK wire on switch to the HOT wire.
•
Connect the WHITE wire on switch to the NEUTRAL wire.
•
Connect the Red wire on switch to the LOAD wire.
•
Connect the GREEN wire on switch to the GROUND wire
or green GROUND screw on box.
DESCRIPTION
The
ZW15SM-PLUS
by itself is a Single Pole switch. Our unique wiring method
combined with Advanced Z-Wave technology allows for multiple switches (requires
ZW3K-N) to control a single Load manually at the devices or remotely from a
computer, smart phone or tablet in Real Time. The ZW15SM-PLUS is fully compatible
with other Z-Wave devices and it can be added to most Z-Wave compliant controllers.
FEATURES
•
Replaces a standard 120VAC, 15Amp wall switch with a technologically advanced
switch that can be manually controlled at the device or remotely through the Z-Wave
network.
•
Set scenes, schedule events (Program ON/OFF times like a timer), and even turn
ON/OFF when a motion or door sensor goes off.
•
Can be used as a Single Pole switch or 3- Way (Multi-location) with ZW3K-N
Auxiliary Switch (sold separately).
•
A blue LED night light can be programmed to come on when the load is ON or OFF.
•
3 Interchangeable Color Face Plates included (white, light almond, and black).
•
Compatible with CFL, fluorescent, incandescent, and halogen bulbs.
•
Measures energy usage of the connected load.
UPGRADING STANDARD SWITCHES TO Z-WAVE
REPLACING EXISTING SWITCHES WITH THE ZW15SM-PLUS
Replacing a standard light switch with a smart Z-Wave switch is a simple way to modernize your home by adding programmable lighting control to your smart
device. The ZW15SM-PLUS Smart Meter Switch enables you to measure the energy usage of your Lights. When added to a Z-Wave network, the ZW15SM-PLUS
reports real time data to your gateway or controller. It can also display actual consumption (in W) and the accumulated power used (in kWh) in the user interface
depending on the Hub. Please refer to your Hub manual for specific instructions on measuring the power.
If you have trouble identifying the
wires, STOP and consult with an
Electrician.
WIRING DIRECTIONS
DO NOT REVERSE THE HOT AND TRAVELER WIRES.
DOING SO WILL VOID YOUR WARRANTY AND THE SWITCH WILL SHORT CIRCUIT.
Step 1.
Identify all your wires. Label the wires or draw a diagram of existing wires. Make sure there is a
NEUTRAL, HOT, and LOAD wire where the ZW15SM-PLUS will be installed.
Step 2.
Connect the wires according to the Diagram.
For 3-Way installation, the ZW15SM-PLUS
requires
the
3-Way Control Auxiliary Switch
ZW3K-N.
A
standard
3-Way switch
WILL NOT WORK
with the
ZW15SM-PLUS. Follow the ZW3K-N Instruction Manual
for 3-Way installation.
REQUIREMENTS
Z-Wave devices require a connection to a compatible hub. Once the device is properly added to
the hub, it can be managed and customized to your needs. Please visit
www.enerwaveautomation.com for a list of compatible hubs. NEUTRAL wire is required.
SPECIFICATIONS
Voltage....................................................
........
....................................
........
................ 120VAC, 60Hz
Incandescent........................................
........
......................................
........
..............................1000W
Ballast....................................................
........
...........................................
........
..
...
....................1200VA
Resistive..............................................
........
..............................................
........
..............1800W(15A)
Motor..................................................
........
.......................................................
...........
............... 1/2 HP
Operating Temperature..........
........
....................................................
..
......................... 32-104° F
Z-Wave Frequency......................................
........
............................
.
....
...
.................... 908.42 MHz
Range....................................................
........
.....
...
................................Up to 1
00
feet line of sight
................between the Wireless Controller and the closest Z-Wave receiver module.
FCC COMPLIANCE STATEMENT
FCC Grant of Equipment Authorizations of this device and transmitters installed in this device can be found at FCC website by entering the FCC ID number on the device.
Caution:
Changes or modifications not expressly approved by the part responsible for compliance could void the user’s right to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
To Replace the Face
Cover, use a small
screwdriver to pry off the
cover
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Electronic
Ballas
t.............................................................................................................................5A
