background image

WARRANTY

This warranty is given by Ensitech Pty Ltd of Unit 1, 144, Old Bathurst Road, Emu Plains NSW 2750, Australia, 
Tel: +61 2 4735 7700, Email: info@ensitech.com.au The benefi ts given by each warranty set out in this 
document are in addition to any other rights and remedies you may have under a law in relation to the 
services or goods to which the warranty relates. Our goods come with guarantees that cannot be excluded 
under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for 
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods 
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major 
failure. Unless otherwise stated you will bear the cost of claiming the warranty.
 

What this warranty covers

This warranty applies to any defects in the goods that appears within 24 months from the date of delivery 
of the goods to you. To claim under this warranty, the defects must be notifi ed to Ensitech and the goods 
returned to Ensitech within two weeks of their appearance. Ensitech will, at its option, replace or repair 
the goods within a reasonable time of receiving a valid warranty claim. Ensitech will pay for the repair or 
replacement but you must pay all other costs including all transport costs of returning the defective goods to 
Ensitech and Ensitech delivering the repaired or replacement part back to you

.

 

How to make a claim

If you want to make a claim under your warranty, please contact Ensitech Pty Ltd in writing by sending a pre-
paid letter to Ensitech Pty Ltd, PO Box 179, Springwood NSW 2777, Australia, or email to info@ensitech.com.
au. You must include your full name, address and contact telephone number and the details of the defect in 
relation to which you make your claim. Ensitech will tell you whether you need to return the goods to Ensitech 
Pty Ltd or the approved local distributor. You will need to return the goods together with all accessories and 

parts for a full assessment and report.

Additional limitations, exclusions and requirements

This warranty does not extend to:

• 

consumables such as the brush, insulating shroud and wand;

• 

any defect caused by normal wear and tear or incidental or inconsequential damage;

• 

any defect caused by misuse, negligence or other abuse of the goods;

• 

any defect caused by accidents or alterations;

• 

goods that have not been cleaned and maintained in accordance with the user’s manual supplied with the 

goods;

• 

loss or damage, including consequential loss or damage, to your work or facilities arising out of or in 

connection with the use of the TIG Brush; or

• 

unless otherwise expressly stated, any right to be reimbursed or compensated for physical or fi nancial 

injury, loss, damage, expense, time or inconvenience (whether direct or indirect) arising out of the 
occurrence of the defect in the product or your inability to use the product.

Model:  

TBE-250         

Serial No.

Purchased from:

Date of Purchase:

Ensitech Pty Ltd 

Unit 1/144 Old Bathurst Road, Emu Plains NSW 2750, Australia

Phone: 

+61 2 4735 7700

  Email: 

info@ensitech.com.au

TIG Brush TBE-250 Instruction Manual   

Feb 2012

TBE-250 Instruction Manual

Feb 2012

Ensitech Pty Ltd

www.ensitech.com.au

Stainless Steel Weld Cleaning System

TBE-250

Operation, Safety and 
Maintenance Manual

Summary of Contents for TIG Brush TBE-250











Reviews: