background image

 

Instruction

 

Manual

 

for

 

enSkate

  

Fiboard

  

 

 

 

I.

 

WARNINGS

 

Do

 

not

 

use

 

enSkate

 

Fiboard

 

until

 

you

 

read

 

and

 

thoroughly

 

understand

 

the

 

owner’s

 

manual.

 

It

 

contains

 

information

 

that

 

is

 

critical

 

to

 

your

 

safety.

 

 

enSkate

 

is

 

not

 

liable

 

for

 

any

 

damage

 

or

 

injury

 

caused

 

by

 

unsafe

 

usage

 

or

 

faulty

 

repair.

 

Any

 

repairs

 

made

 

to

 

this

 

product

 

by

 

unauthorized

 

technicians

 

are

 

the

 

sole

 

responsibility

 

of

 

the

 

owner.

 

 

Fiboard

 

is

 

only

 

for

 

people

 

16

 

years

 

and

 

older.

 

 

While

 

riding

 

Fiboard,

 

always

 

wear

 

protective

 

gear,

 

including

 

knee,

 

elbow,

 

and

 

wrist

 

guards

 

and

 

an

 

approved

 

safety

 

helmet,

 

when

 

riding

 

Fiboard.

 

 

Only

 

use

 

Fiboard

 

on

 

paved

 

surfaces

 

or

 

on

 

gentle

 

slopes.

 

Do

 

not

 

use

 

on

 

dirt,

 

sand,

 

steep

 

slopes,

 

or

 

slippery

 

surfaces.

 

Be

 

cautious

 

when

 

going

 

down

 

hills.

 

 
 

II.

 

Introduction

 

to

 

Fiboard

 

 

2

1

 

Schematic

 

diagram

 

and

 

description

 

of

 

Fiboard

 

Summary of Contents for Fiboard



































Reviews: