background image

                     INSTALLATION MANUAL ON CISS FOR PRINTER EPSON C82/C80/C70

                     

 1 

Installation Manual on  

Continuous ink supply system (CISS) 

For printer EPSON 

C82/C80/C70

  

 

Thank you for using the “INKSYSTEM” Continuous ink supply system. It is the 

best  device  for  an  inkjet  printer,  and  it  will  definitely  decrease  your  printing  costs. 
Before using this system, please read this manual carefully. The pictures in this manual 
may be different with the real ones. It’s just for your reference. 

 

Note: The pictures in this manual may be different with the real ones. Here just 

for your reference.  

 

         I. Opening Guide 
 

1. Accessories 

1) Continuous ink supply system ……………………………………………1  
2) Air Filter ………………………………………………………………….1  
3) Sponge …………………………………………………………………….1 
4) Injector …………………………………………………………………….1 
5) Long needle …………………………………………………………….....1  
6) Short needle …………………………………………………………….....1 
7) Protection clamp …………………………………………………………..1 
8) Installation Manual ………………………………………………………..1 

9) Certificate on free installation………………………………………………1 

  

 

                           

              Pic. 1-1                                                      Pic. 1-2 

 
2. Inspection before installation 

A. Check whether all the accessories are present.  
B. Check whether the system is retrieved normally or too much air is remained in 

the connecting tubes (length over 20cm). 
 

II. Printer test 

Summary of Contents for Stylus C82







Reviews: