3. Function and Intended Use
The solar lamp
is designed for all season outdoor use
. It may either be
operated floating on a water surface or standing on the ground. If the lamp
is operated floating, it has to be taken from the water surface in case of
frost.
An aluminum bottom prevents the globe from tumbling in case of wind on
the water surface or on the ground. When the lamp is mounted on the
ground it is additionally possible to use the 2 enclosed ground spikes to
fasten it in the ground.
The solar lamp has to be set up free from shadows and facing the sun.
Recommended are south, east or west sides. Shadowy north sides are not
appropriate for solar lamps.
The light color is alternating or lockable. This can be set by the infrared
remote control included in the scope of delivery.
The integrated rechargeable battery is charged by the solar module
installed inside the lamp. The lamp is automatically switched on when it is
getting dark and switched off at dawn or if the battery is discharged.
Powerful light emitting diodes (LEDs) are used as light source
.
Those LEDs
guarantee a high luminosity with a low current consumption and a lifetime
of more than 50000 hours.
Note:
During longer periods with insufficient insolation, the accumulator is
charged insufficiently via the sunlight. However, that does not mean that
the solar lamp is defective. Please wait for the next sunny days and the
light will work accordingly.
The rechargeable battery has to be exchanged every 2 years on
average!
4. Putting into Operation
1.
Please carefully take all parts out of the package
.
2. In order to avoid any discharging of the battery during the storage period,
this battery has to be installed before putting the lamp into operation. A bag
with the parts required for the assembly is included in the scope of supply.
Proceed as follows when installing the battery:
3. Open the bag and put the parts onto a table.
4. Take the rechargeable battery and insert it in the battery
compartment with the correct polarity (illustration 1).
5. Firmly press in the main switch of the lamp „SM1“ on the circuit
board (illustration 2). (The switch SM2 is of no significance for the
putting into operation. It only serves for the control of functions
during service operations).
6. Now precisely insert the gasket into the groove (illustration 3).
7. Attach the aluminum lid. Make sure that the black bracket is above
the battery (illustration 4). The bracket protects the battery from
falling out in case of convulsions.
8. Now take the 4 screws and slightly tighten them manually
(illustration 5). Now take the enclosed tool and slightly tighten the
screws clockwise one after the other.
9. In a 2. and 3. stage (illustration 6) tighten the screws firmly. The
tightening in several stages prevents an irregular seat of the cover.
Thus, the lid sits flatly and tightly on the gasket.
Operating Instructions
Solar Floating light „Float 25“ multicolor
1. Introduction
Dear customer, we thank you for purchasing the Solar Globelight.
With this Solar Light you have purchased a product that complies with the
latest and most up-to-date technology.
This product complies with the European and National
Standards. The relevant certificates of conformity are
deposited with the manufacturer.
To preserve this standard and in order to maintain safety
you must adhere to the use instructions!
2. Security Instructions
In the event of any problems arising or damage occur-
ring from not following these instructions, the warranty
is deemed cancelled. The manufacturer will not be held
responsible for any claims or damages arising from the
misuse of this product.
- For safety reasons and in order to maintain standards (CE) you are pro-
hibited from altering or changing any component in the product.
- Please follow the instructions very carefully.
- For commercial applications due care and attention must be paid to the
Health and Safety Standards in your jurisdiction.
Battery take-back
- Batteries must not be discarded into domestic waste.
- The consumer is legally required to return batteries
after use, e.g. to public collecting centers or to battery
distributors.
- Contaminant-containing batteries are labeled with the
sign “crossed-out trashcan“ and one of the chemical
symbols. Used batteries should be disposed environ-
mentally friendly and should not be discarded into
domestic waste. Your dealer is legally required to take
back old batteries.
NiMh
GB
Customer support:
If you have problems or questions regarding this product, simply contact us!
esotec GmbH, Industriegebiet Weberschlag 9, D-92729 Weiherhammer
Monday to Friday 9 am to 12 noon and 1 pm to 4 pm.
By phone: +49 9605-92206-0
By e-mail for ordering spare parts: ersatzteil@esotec.de
By e-mail for questions about the product: technik@esotec.de
Rechargeable battery notes
- Rechargeable batteries should not be played with by children. Never
leave rechargeable batteries lying around; they could be swallowed
by children or pets.
- Rechargeable batteries must never be short-circuited, disassembled
or thrown into fire. This leads to a danger of explosion!
- Leaking or damaged rechargeable batteries can cause chemical
burns when they come into contact with skin. For this reason, please
make use of suitable protective gloves.
- Rechargeable batteries should only be replaced by structurally iden-
tical rechargeable batteries from the same manufacturer. Normal
batteries must not be used since these are not rechargeable.
- Make sure the rechargeable batteries are inserted with the correct
polarity.
- For long periods of time of non-use (for example, storage), remove
the inserted rechargeable batteries to avoid damages via the leaking
rechargeable batteries.
Disposal:
Dear customer,
please cooperate in avoiding waste. When you intend to
dispose of the product in future, please consider that it
contains valuable raw materials suited for recycling.
Therefore, do not dispose it of with domestic waste but
bring it to a collection point for the recycling of waste
electrical and electronic equipment.
Thank you very much for your cooperation!
!
1.
2.
3.
4.
5.
6.
2-3x
