ETC ColorSource Spot jr Installation Manual Download | Manualshive

Page: 1 / 12

background image

ETC Installation Guide

ColorSource Spot jr

Corpora te He a dqua rte rs Middleton, WI, USA +1 608 831 4116
London, UK +44 (0)20 8896 1000 Holzk irc he n, DE +49 (80 24) 47 00-0
Rome , IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 P a ris, FR +33 1 4243 3535
We b

Support

support.etcconnect.com

Conta c t

etcconnect.com/contactETC

© 2020 Electronic Theatre Controls, Inc.

Product information and specifications subject to change. ETC intends this document
to be provided in its entirety. Trademark and patent info:

etcconnect.com/ip

7 4 1 6 M 2 1 0 0 -2 .0 Rev B Released 2020-06

Overview

The ColorSourceSpot jr provides built-in zoom capability and uses the RGB-L
(red, green, blue, and lime) color system to provide a rich, bright light.

The ColorSource Spot jr is available in both original and Deep Blue variants.
The Deep Blue uses an array that offers richer, more saturated blues and
stronger magentas in exchange for the more jewel-toned blues like sky or
turquoise. For more information, see the ETC website at

Note:

Features described in this document require the latest version

of software. For information on updating fixture software, see

the Fixture Software on page 10

1
2
3
...
»

Summary of Contents for ColorSource Spot jr













Reviews:

No comments

Related manuals for ColorSource Spot jr

Brand: DTS Pages: 44

LED SOLAR SPOTLIGHT

Brand: LIVARNOLUX Pages: 88

Brand: Cameo Pages: 192

Brand: Anslut Pages: 9

Brand: Anslut Pages: 11

Brand: Anslut Pages: 20

Brand: Anslut Pages: 19

Brand: NANLITE Pages: 25

Brand: Larson Electronics Pages: 2

Brand: Larson Electronics Pages: 4

Brand: Vector Pages: 8

Collins Fixed-Mounted Hid Spotlight CD-FX-HID-1

Brand: Havis-Shields Pages: 2

Premium City SH2705

Brand: brennenstuhl Pages: 84

Brand: Whelen Engineering Company Pages: 4

Brand: Mark Pages: 4

Brand: Volt Pages: 8

Brand: STEINEL Pages: 62

Brand: Robert Juliat Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands