background image

 

 

[1] 

 
etzMAX‐light/m/plus 

Coffee Grinder with Conical 
Burrs for commercial use

 

 

Congratulations on the purchase of your 
new ON‐DEMAND “etzMAX” espresso 
grinder!  
 

The etzMAX is one of the 
fastest and most precise espresso grinders 
on the market.  

 

 

 

 
The team at “Etzinger” would like to wish you happy coffee grinding with your new 
“etzMAX”! 

 
_______________________________________________________________________________________

 

 
INTRODUCTION

 

 
Before  operating  the  device  (referred  to  in  these  operating  instructions  as  the  “coffee  grinder”, 
“grinder”,  or  “device”),  please  read  the 

operating  instructions  and  safety  information

  carefully. 

Keep the operating instructions in an 

easily accessible location

 so that you and anyone else who 

wishes to use the device has access to them.  

Persons who operate the device must have been properly instructed beforehand. 

Any use not as 

intended or failure to observe the safety information can lead to damage to the device and/or 
hazards to the health of the operator.

 Do not make any modifications to the device. Neither the 

manufacturer  nor  the dealer  shall be  liable  for  any  injury or  damage  sustained  due  to  failure  to 
observe the safety information. This Operating Manual is based on EU‐norms and regulations.  

The espresso grinder is only designed for the grinding of full coffee beans. 

In the event of queries and/or for further information concerning this device, please contact the 
manufacturer or your dealer. 
 
For further information, please visit 

www.etzinger‐ag.com

 or contact us directly (+423 375 

8383/support@etzinger‐ag.com) 

 
ETZINGER AG, Wirtschaftspark 44, FL‐9492 ESCHEN 

Summary of Contents for etzMAX-light




























Reviews: