Z-Wave Smart Plug
(2 Channel)
• ZW37 •
Model: MP20Z
Power: 120V AC, 60Hz
Loading: 10 Amp Max Smart Outlet *1
10 Amp Max Smart Outlet *1
Total(Both Outlets): 16 Amp Max
Frequency: 908.42MHz
Put the Z-wave interface controller into “Add” mode,
triple press the Program button.
It will be included in
network. (Once your controller confirmed, refresh
the Z-Wave network to optimize performance. )
Put the Z-Wave interface controller into "Remove"
mode,
triple press the Program button
. It will be
excluded to network.
Press and hold button 5S while power on.
Note: This should only be used in the event your
network’s primary controller is missing or otherwise
inoperable.
2. Your device may need to be within 100 feet of the
controller to be included. If so, include the device
to the network within 10 feet of the controller
and relocate it to the desired position in your
home. Be sure to refresh the network if the
device is included in this manner.
Add to Z-Wave Network
Remove from Z-Wave Network
1. Plug the device you want to control into the
Z-Wave Smart plug controlled outlet.
NOTE: Plug directly into the outlet, do not use
with extension cords.
To return your switch to factory defaults
100 feet
Features:
Notes:
Program button
Smart outlet*2
Single press : manually turn
on/off your device.
Two outlets can remotely
turn On/Off the
connected device.
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices
from other manufacturers and/or other applications. All non-battery operated nodes within the
network will act as repeaters regardless of vendor to increase the reliability of the network.
This Device supports Lifeline (association group 1) supporting 1 node for lifeline communication.
Group 1 must be assigned the Node ID of the primary controller where unsolicited notifications will be
sent. The Z-Wave controller should set this association automatically after inclusion.
Lifeline association only supports the “Device Reset Locally” function. Refer to the instructions of your
controller for any available details on how this can be set.
1. Z-Wave on/off control of 2 electrical devices.
2. Two Z-Wave controlled AC outlet for standard
incandescent lighting, CFL/LEDs, fans or small
appliances(1800W Resistive).
3. Grounded 3-wire power connection for safety.
4. Manual/wireless on/off and brightness control.
5. Remembers and restores on/off status after power
failure.
6. Built-in Z-Wave Plus signal repeater to extend
network range.
7. S2 security and 500 Z-Wave chip for reliable
wireless communication.
8. Work with all certificated Z-Wave controllers.
1. ADD/REMOVE:
Triple press the button, LED will brink within 30s
press 1x: On/Off the Right outlet
press 2x: On/Off the Left outlet
press 3s: On/Off simultaneously.
2. Factory setting:
Manual: Click Z-Wave button 2 times quickly, and hold
for at least 10 seconds
Host reset: Remove it from the host and the device is
factory reset.
3. Association
(Support 3 group, each group max
support 2 devices) LED flash twice to confirm its setup
successfully.
Group 1 lifeline
Group 2 Left outlet sends a basic set
Group 3 right outlet sends a basic set
4. LED Indicator
Manual: Click Z-Wave button 6 times quickly to change
between values 0,1, 2
Parameter =1, size =1byte, value=00 Default out on,led on,
value=01 out on,led off
value=02 led no work
5. Auto Turn-Off Timer
Parameter =2, Size=4
，
Values: 1 – 65535 (minutes);
turn off the left outlet
Parameter =3, Size=4
，
Values: 1 – 65535 (minutes)
turn off the right outlet
6. Auto Turn-On Timer
Parameter =4, Size=4
，
Values: 1 – 65535 (minutes);
turn on the left outlet
Parameter =5, Size=4
，
Values: 1 – 65535 (minutes)
turn on the right outlet
