background image

Page 1 of 5 

109-6457 Rev. A 

 

 
 

Loose Parts 

Note:  

Use the chart below to verify that all parts have been shipped. 

109-4173 

Dealer Pack  

Part # 

Description 

Qty 

Use 

103-1309 

Warranty Registration Form 

Fill out and return to Exmark 

103-2106 Key 

1 Unit 

ignition 

1-633023 

322-3 

3256-23 

1-805005 
1-633349 

3296-47 

Stud, Fuel Tank 
Screw, HH 5/16-18 x 3/4 
Washer, 5/16 SAE 
Washer, Lock 5/16 Heavy 
Spring, Compression 
Nut, Nyloc 5/16-18 Thin 






Components to install fuel tank 

323-6 

98-5975 

3290-357 

Screw, HH 3/8-16 x 1 
Washer, Spring Disk 3/8 
Nut, Whizlock 3/8-16 



Components to install handle assembly 

1-806003 
1-808280 

Hairpin, Cotter 
Pin, Clevis 5/16 x 1 


Components to install the speed control rod assembly 
& to connect the lower end of the speed control linkage 

3220-16 

322-9 

3296-29 

Nut, Jam 3/8-24 LH 
Screw, HH 5/16-18 x 1 3/4 
Nut, Nyloc 5/16-18 



Components to install drive lever linkages 

1-303335 
1-303287 

Tie, Cable 7 15/16 (Large) 
Tie, Cable 5 1/2 (Small) 


For fastening wiring harness to handle assembly 

 

109-4175 

Literature Pack 

Part # 

Description 

Qty 

Use 

------------ 
------------ 

Manual, Operator’s 
Manual, Parts 


Read before operating machine 

103-5466 

Manual, Engine Operator’s 

For units with 15HP Kawasaki engines 

103-6371 

Manual, Engine Operator’s 

For units with 17HP Kawasaki engines 

103-6374 

Manual, Engine Operator’s 

For units with 19HP Kawasaki engines 

109-6435 Sheet, 

Emissions 

Warranty  1  

 

 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 

TURF TRACER HP

SETUP INSTRUCTIONS

For Serial Nos. 670,000 and Higher

Summary of Contents for 109-4173






Reviews: