background image

Page 1 of 5 

109-4291 Rev. A 

 

 
 

Loose Parts 

Note:  

Use the chart below to verify that all parts have been shipped. 

109-2996 

Dealer Literature Pack  

Part # 

Description 

Qty

Use 

323-9 

13-2840 
3296-39 

3247-4 

109-4492 

Cap Screw, Hex 3/8-16 x 1-3/4 
Key, Square 
Nut, Nyloc, 3/8-16 
Set Screw, 3/8-16  
Washer, Special 





Installing the PTO Shaft 

103-1309 

Warranty Registration Form 

Fill out and return to Exmark 

 

109-1303 

Literature Pack 

Part # 

Description 

Qty

Use 

109-4290 

Manual, Operator & Parts 

Read and view before operating machine 

 

WARNING

 

POTENTIAL HAZARD 

  Operating a FrontRunner tractor without an 

approved Exmark front mount attachment 
increases the possibility of forward tip over. 

WHAT CAN HAPPEN 

  Tip-over could cause serious injury or death. 

HOW TO AVOID THE HAZARD 

  When operating a FrontRunner tractor without 

an approved Exmark front mount attachment, 
observe the following: 

9

 

Limit operation to minimum required to 
install a different front mount attachment. 

9

 

Minimize speed and use extreme caution. 

9

 

Only operate on a flat level surface. 

9

 

Do not operate up or down a trailer ramp. 

9

 

Avoid sudden acceleration or deceleration. 

Uncrate Deck 

1.  Remove top and sides of crate from base. 

2.  Remove straps securing front frame and deck to 

crate.  

 

 

 

 

 

Lowering the Discharge Chute 

1.  The discharge chute is shipped in the “up” 

position.  

2.  Slightly loosen the two bolts enough to rotate 

the discharge chute to the down position.     
(See Figure 1) 

3.  Snug tighten the two bolts just enough to cause 

some drag when rotating the chute. 

 

 

 

 

 

 

 

 

 

FIGURE 1 

Installing the PTO Drive Shaft 

1.  Cut zip ties securing drive shaft to crate.  

2.  Remove tape from shaft and key. 

3.  Insert square key on the input shaft on the 

gearbox and then slide shaft into the PTO yoke 
until it contacts washer. (See Figure 2) 

 

FRONTRUNNER

®

 52” & 60” DECK

SETUP INSTRUCTIONS

For Serial Nos. 600,000 and Higher

Summary of Contents for FRONTRUNNER 52






Reviews: