Extron electronics TLP Pro 1220TG, Setup Manual

1

Product Category

IMPOR

TANT

:

Go to 

www

.extron.com

 for the

complete user guide and installation

instructions befor

e connecting the

product to the power sour

ce.

TLP Pro 1220TG, TLP Pro 1520TG,  
and TLP Pro 1720TG • Setup Guide

Overview

The Extron TLP Pro 1220TG, TLP Pro 1520TG, and TLP Pro 1720TG are table-top touchpanels with high resolution capacitive 
touch screens. The TLP Pro 1220TG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1520TG has a 15.6 inch 
screen with a 1366x768 resolution. The TLP Pro 1720TG has a 17.3 inch screen with a 1920x1080 resolution. They are ideal for any 
AV applications requiring large touchpanels with flexible mounting options and fully customizable interfaces. This guide provides 
instructions for experienced installers to mount and install these touchpanels. For more complete procedures, see the 

TLP Pro 1220, 

TLP Pro 1520, and TLP Pro 1720 Series User Guide

 at 

www.extron.com

.

Setup Overview and Checklist

Get Ready

Download and install the latest version of the following software:

z

GUI Designer

 — for designing layouts for Extron TouchLink

®

 Pro touchpanels and third party touch interfaces.

z

Global Configurator

®

 Plus and Professional 

— for setting up and configuring the control processor and touchpanel.

z

Toolbelt 

— for device discovery, device information, firmware updates, and configuration of network settings, system 

utilities, and user management for TouchLink Pro devices. 

All three software programs are available from 

www.extron.com

.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you also require:

IP address 

Subnet mask

Gateway

User name — this can be either 

admin

 or 

user

.

Passwords  — by default, these are 

extron

 (for both admin and user).

Make a note of the touchpanel MAC address.

Mount and Cable All Devices

ATTENTION:

• 

Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply section of 
the 

TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series User Guide

 or the 

IPL Pro User Guide

.

• 

Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section « sources 
d’alimentation » du 

TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series User Guide

 ou du 

IPL Pro User Guide

.

Mount the units. There are several mounting options for TouchLink Pro touchpanels (see 

Mounting

 on the following page). 

Connect cables to the touchpanels. To connect cables, remove the back and base covers (see 

figure 1

 on the following page). 

For more information about the cable connectors, see 

Rear Panel Features

 on page 4.

Connect the power cords and power on all devices.

Set up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor, and touchpanel 

to the same Ethernet subnetwork

.

Use the 

Setup Menu

 (see page 5) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, gateway, 

and related settings for the touchpanel.

Configure the Touchpanels

The 

GUI Designer Help File

, 

Global Configurator Help File

, and the 

Toolbelt Help File

 provide step-by-step instructions and more 

detailed information. The 

Global Configurator Help File

 includes an introduction to the software and sections on how to start a 

project and configuration.