Using C5630(black), C5626(white) 2.4GHz Cordless Phone
Version 2010003
to make or answer a call.
to make or answer a call using
speakerphone.
to end a call.
To redial the last number.
O
(Program):
to program a number into
memory button
to dial the number stored in
memory.
▲
After pressing
button, to increase
receiver volume and tone amplification.
After pressing
button, to increase
speaker volume and tone amplification.
▼
After pressing
button, to decrease
receiver volume and tone amplification.
After pressing
button, to decrease
speaker volume and tone amplification.
Retain Amplification:
LED light to indicate
amplification settings are retained for future
calls.
Retain Amplification switch –
set to
On
to save amplification level for
future calls.
Neckloop:
a 3.5mm audio out jack.
Headset:
a 2.5mm jack for headset.
Tone:
set to Hi for extra high
frequency amplification. Set to low for
extra low frequency amplification.
Ringer:
to set ringer volume.
Desk Mounting
Plug one end of the 12 foot line cord into the jack labeled “
Line
” on
the bottom of phone and plug the other end into a wall jack. The
wall mount bracket is not recommended for desk top use.
Wall Mounting
Insert the wall mount bracket into two holes
labeled “WALL” on the bottom of phone base.
1. Plug one end of the 7 inch line cord into the
jack labeled “
Line
” on the bottom of phone
and plug the other end into the jack on the
wall plate.
2. Slip the mounting holes (one on wall mount
bracket and one on rear edge of base) over
the wall plate posts and firmly slide the unit into place.
Charging batteries
Pull the tab around handset battery compartment. Battery will make
contact with charging circuit. Place the handset on the base unit for
6 hours before initial use.
Optional Swappable Rechargeable Batteries
Optional rechargeable batteries can be installed in the base unit. In
case of commercial power failure, you can continue to make or
receive phone calls. Duration of operation is limited by talk time and
standby time.
If you wish to use the handset when battery is low, you may swap
the base batteries with the handset batteries. You can continue to
make phone calls when batteries are recharged in the base
.
Retain Amplification
Set the
Retain Amplification
switch to
On
(
Retain Amplification
LED is lit), the receiver volume amplification level is saved
automatically and used for all future calls.
If the
Retain Amplification
switch is set to
Off
, receiver volume is
reset when you replace the handset in the handset cradle.
Adjusting Handset Receiver Volume
To adjust the handset receiver volume during a phone call:
1. Press the
▲
button to increase the receiver volume
2. Press the
▼
button to decrease the receiver volume.
3. Stop adjustment when you can hear words most clearly.
Warning: Excessive handset receiver volume when the Retain
Amplification LED is lit.
Adjusting the Ringer Volume
The
"RINGER"
switch on the right side of the phone and base
controls the volume. You can set the
"RINGER"
switch to "
Hi
" for
a high volume ring, "
Low
" for a low volume ring or "
Off
" to turn the
ringer off. The Visual ringer flashes for all incoming calls regardless
of the ringer setting.
Programming the Memory Button
You can program a telephone number into the
button for one-
touch speed dialing.
1. Press the
O
Program button.
2. Press the
button.
3. Enter a telephone number
4. Press the
O
Program button again.
Making a Call
1. Pick up the
Handset
and press the
. If you wish to use
speakerphone, press the
button.
2. Using the
Keypad
, dial the desired telephone number.
Receiving a Call
1. When you hear the phone ring, pick up the handset from the
handset cradle and press the
or the
button.
2. When you are finished talking, replace the handset in the
handset cradle or press the
to end the call.
Talkback Buttons and Audio Instructions
When a button is pressed, it talks back. You can know a button is
pressed incorrectly without looking.
To disable talkback feature, press
#OFF#
or
#633#.
Phone
announces “
talkback feature is off
”.
To enable talkback feature, press
#ON#
or
#66#.
Phone announces
“
talk back feature is on
”.
To read out amplification setting, press
##
, Phone announces,
“Amplification setting is retained for future calls. Volume is set to
level 6.”
To read out basic operation instruction, press
**.
