background image

MLED-CTRL Box 

User manual 

 

 

 

December 2021 - Version EN 1.2 

www.fdstiming.com

 

                                                        

 

1.

 

Presentation  

 

1.1.

 

Switches and connectors 

 

1) Active GPS antenna (SMA connector) 
2) Radio antenna 868Mhz-915Mhz (SMA connector) 
3) Validation switch (Orange) 
4) Selection switch (Green) 
5) Audio out 
6) Input 1 / temperature sensor 
7) Input 2 / Sync Output 
8) RS232 / RS485 
9) Power connector (12V-24V)  

Only for model with SN <= 20 
If SN > 20 power connector is on the back 

 
 
 

1.2.

 

MLED assembly 

 

The most common configuration comprises of 3 or 4 x MLED panels adjoined to form a 
display fully configurable to either a single full height line of characters or multiple lines as 
below. Another configuration proposed is 2 rows of 6 modules which form a 192x32cm 
display area. 
The total display area is divided into 9 zones (A – I) as the schematic below. Be aware that 
some zones share the same display area and should not be used together. A line number as 
well as a color can be assigned to each zone via the IOS or PC setup application.  
It is recommended to assign the value “0” to any unused zone. 
The MLED-CTRL box must always be connected to the lower right MLED module. 

 
 

 


 

 

Summary of Contents for MLED-3C




















Reviews: