FEATURES
1
High Intensity LED headlamp.
2
Extra spot beam.
3
Cool or neutral white LED version available.
4
IPX4 Water resistant.
5
1000 lumens for 16 hours.
6
8 Selectable brightness levels from 10% to 80%.
7
4 selectable blinking modes: police blinking, slow blinking, quick
blinking, and SOS.
8
Smart IC motherboard provides multiple brightness settings ,and
prevents overheat, over discharge or damages caused by polar
reversing.
9
The light will emit 10 successive blinks in 8 seconds when Battery
level indicating around 20% capacity.
10
Elastic bungee headband capable of length adjustment, providing
best fit and comfort for user.
11
Optional Diffuser and USB cable charger available.
12
Optional BP2836B, BP4836B and BP6836B for longest runtime each
9 hours, 18 hours and 27 hours on High.
USAGE INSTRUCTIONS
1
Briefly press the rubber switch to turn the HL20AAII on/off.
2
The HL20AAII provides three lighting options:
•
Maximum brightness: 100% output
•
Custom brightness: eight selectable modes ranging from 10% to
80% output
•
Strobe / SOS: police strobe, slow strobe, rapid strobe and SOS.
3
Operating Instruction:
•
i) To turn the HL20AAII on, briefly press the rubber switch. The default
setting is maximum brightness (100% output).
•
ii) To access custom brightness mode: with the HL20AAII turned on
(in either max or custom mode), hold the switch down for more than
2 seconds and the HL20AAII will cycle through 8 levels of output.
When a desired output is displayed simply release the button to set
the brightness.
•
iii) The HL20AAII has 3 hidden strobe modes and 1 SOS mode. To
access these modes simply hold down the power button for 2
seconds with the unit turned off and release. To cycle to the next
strobe / SOS mode once again hold for 2 seconds and release. To
exit strobe / SOS mode simply press the switch once (turns the
HL20AAII off).
4
Low battery warning:
When the battery capacity gets very low
(approx. 20%), the HL20AAII will emit 10 successive blinks in 8 seconds.
This is a reminder that the battery should be replaced.
5
Reverse polarity protection:
When a battery is inserted incorrectly,
a special protection circuit will activate and automatically prevent
operation to ensure the safety of the HL20AAII and its user.
6
The HL20AAII is also designed with intelligent over-discharge
detection. If battery voltage reaches a critical lower limit, the HL20AAII
will automatically turn off, at which time the battery should be
replaced as soon as possible.
WARNING
•
Do not use batteries that are banned on this manual.
•
Do not mix batteries of different brands, size, capacity or type.
•
Be sure to operate the battery box as per the correct instructions so
to avoid any damage.
DIAGRAM
INSTALL AND REMOVE THE BATTERY BOX
AA BATTERY BOX INSTRUCTIONS
USER MANUAL
High intensity
LED Headlamp
HL
20
AA
II
UNSCREW THE NUT
BOTH NUTS ARE UNSCREW
REMOVE THE SCREW CASE FROM
BATTERY BOX
INSET 3PCS 1.5V AA BATTERY
WITH THE CORRECT POLAR IN AA
BATTERY BOX
PUT THE SCREW CASE IN THE RIGHT
DIRECTION
SCREW UP BOTH NUTS ON AA BOX
ADJUSTMENT BUCKLE
NYLON ELASTIC BAND
HEAD
LED
ADJUSTMENT
DIRECTION
SWITCH
5.5 DC PLUG CABLE
BATTERY BOX 3*AA
*
PHOTOS ARE FOR REFERENCE ONLY, PRODUCTS IN KIND PREVAIL!
TWO RUBBER BELTS TO TIGHTEN
ON AA BOX
CONNECT THE 5.5DC PLUG OF HEADLAMP AND THE 5.5 DC JACK
OF AA BOX, AND THEN SCREW UP THE HOLDER
THE DIRECTION OF DC JACK FOR
AA BATTERY BOX SHOULD BE TO
SWITCH BOX OF HEADLAMP
PUT THE AA BOX THRU THE RUBBER
BELT