background image

InstallatIon InstructIons

skIrted het two pIece toIlet 

Tools Needed

A. Screw Driver  
B. Adjustable Wrench  
C. Marker  
D. Tape Measure  
E. Level  
F. Drill  
G. Toilet Flange 
H. Wax Ring  

I.  T-bolts (2), Nuts (2), 

Washers (2)

J. Flexible Supply Tube

Items Included

K.  Fixing Screws (2),  

Decorative Caps (2),  

Cap Base (2)

L.  Flange Connecting  

“L” Brackets (2)

Note:

 Views in this illustrations are for general representation and may not necessarily define the exact contours of the product.

Remove Old Toilet 

Shut off water supply line to toilet. Flush toilet 
and remove all water from the bowl and tank 
using a sponge. Disconnect the water supply 
from the tank. Remove the tank from bowl, 
use a screw driver and adjustable wrench or 
socket wrench. Loosen toilet bowl flange nuts 
under bolt caps. Remove old bowl by carefully 
lifting it off the floor. Clean flange and plug 
drain with a rag to prevent sewer gas from 
escaping. Replace or repair if required.

Install Connecting “L” Brackets and 

the Wax Ring Seal

1.  Check the rough-in dimension, this is the 

distance from wall to center of outlet. 

2.  Place two new T-connection bolts into the 

slot on the toilet flange. 

3.  Install the connecting “L” brackets onto 

the T-bolts with the flat side toward the 
outside of the flange, adjust the spacing 
on the outside of the bracket to be 8-1/4

"

 

(210mm), now attach the washers and nuts 
to the T-connection bolts and tighten the “L” 
brackets snug and direct to the floor flange. 

4.  Set the wax ring into the outlet between the 

T-connection bolts.

Install Water Closet Base

1.  Place toilet bowl upside down on clean 

surface. 

2.  Install a bead of sealant or plumbers putty 

around the outside foot base on 3 sides. 

3.  Now lift the bowl over the flange and  

lower the bowl into place allowing the “L” 
Brackets to align with the holes on the skirt 
of the toilet bowl.

4.  Firmly push the toilet down seating the bowl 

horn into the wax ring seal. 

5.  Set the bowl in place by gently rocking back 

and forth on the bowl rim. The “L” brackets 
should extend up through the slots on both 
sides of the outlet horn. 

6.  With bowl firmly set, insert fixing screws 

into the seat base, slide the connection 
screw and base into the flange  
connection holes and tighten on both sides 
of the bowl evenly until snug. 

7.  Snap decorative cap over connection  

screw head.

A.        B.           C. 

D.

E.

F.

G.

H.

I.

J.

K.

L.

Flange 

Connection 

Holes

Sealant or  

Plumber Putty

Outlet Horn

Decorative Cap

Connection Screw

Base

Floor 

Outlet 

Flange 

8-1/4

"

 (210mm)

 

          Important

T-Bolts

T-Bolt, 

Nuts & 

Washer

Wax Ring

NOTE: 

If installing the PF9002SWH please disregard the installation instructions included with the tank and use this set of installation instructions

Summary of Contents for PROFLO PF9002SWH













Reviews: