background image

www.fieldcontrols.com

Please retain these instructions after installation.

This device MUST be installed by a qualified agency in accordance with the manufacturer's installation instructions. The definition of 
a qualified agency is: any individual, firm, corporation or company which either in person or through a representative is engaged 
in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the 
precautions required, and has complied with all the requirements of the authority having jurisdiction.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.

Installation Date:

Installed By:

Phone:

UV-AIRE™ AIR PURIFYING SYSTEM

Model: UV-13FM, 17FM

UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a homes’ heating 
and air conditioning system.  The treatment is a safe, silent, and proven way to make your home a healthier place 
to live.

ITEMS INCLUDED IN KIT:

•  Twin-Tube High-Output UVC Lamp
•  24 VAC Ballast* (UL listed) with Lamp Cable connector
•  Lamp Cable with connector
•  FlexMount™ Articulating Bracket Assembly with Magnet (patent pending)
•  Shield Assembly
•  Snap-In Safety Viewport
•  UV Hazard Warning Label
•  Alcohol Wipe for Lamp
•  Installation & Operation Manual

*50 VA Transformer required (not included), order part # 46638900 TR50VA or equivalent.

WARNING: Never expose eyes or skin to UVC light from any source. Looking directly at the UVC light may 
cause permanent eye damage or blindness. Never operate the UV-Aire™ Air Purifying System out of the 
plenum. Avoid touching the glass portion of the lamp with your hands.

Summary of Contents for FlexMountUV UV-AIRE Series









Reviews: