background image

Page 1 

 

Model: 15-2N-ATV-GS 

(5303197) 

 

(15 Gallon ATV Sprayer)

 

www.fimcoindustries.com 

1000 FIMCO Lane, P.O. Box 1700, North Sioux City, SD  57049      

Toll Free Phone: 800-831-0027 : Toll Free Fax: 800-494-0440 

[5195533   

 

 

 

 

 

(10/20)] 

Technical Specifications 

 

15 Gal. Corrosion-Resistant Polyethylene Tank 

 

12 Volt Diaphragm Pump, 1.2 GPM - 60 PSI 

 

15 Ft. Handgun Hose (3/8” I.D.) 

 

12 Ft. Vertical throw, 20 Ft. Horizontal Throw 

 

2-Nozzle Boom Assembly (80” Spray Coverage) 

 

Corrosion-Resistant Nylon Nozzles 

 

Check Valve Strainers, 50 Mesh, 5 PSI 

This sprayer may be mounted to most makes  
of agricultural ATV vehicles. 

Caution: When fully filled with water, this sprayer will 

weigh approx. 160 lbs.. Consult the owner’s manual for 

your vehicle to verify that you are within it’s load carrying  

capacity.  

Assembly Instructions 

 

Make sure the contents of the sprayer’s carton match the 
items shown on page 2 of the manual. 

 

Follow the steps on pages 2 & 3 to properly assemble the 
sprayer. 

 

After assembly is complete and before testing your spray-
er, make sure you connect the electrical hook-up to the 

end of your pump and clip the clips to a fully charged bat-

tery. 

 

The drain plug assembly should already be attached to the 
tank 

 

Make sure all hose clamps are tight before testing or 
spraying  for the first time. 

***IMPORTANT REMINDER*** 

You must occasionally check and clean the strainer screen, located on the 

inside of the tank, especially if you experience a sudden loss of pressure. 

OWNER’S MANUAL

 

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON, PLEASE CALL

1-800-831-0027

MONDAY-FRIDAY, 8:00 AM TO 5:00 PM CST

If you should have a question or experience a problem with

your Fimco Industries Product: Visit our website @ 

www.fimcoindustries.com or call the Toll free number above. Our 

technical support representatives will be happy to help you. 

In most cases a customer service rep. can resolve

the problem over the phone.

To obtain prompt, efficient service, always remember to give the 

following information....

• Correct Part Description and/or part number

• Model number and Serial Number

Part descriptions and numbers can be obtained from the

illustrated parts list section(s) of this manual.

General Information 

Thank you for purchasing this product. The purpose of this 

manual is to assist you in operating and maintaining your lawn 

& garden ATV sprayer.  

Retain a copy of your receipt for your 

unit, as it will be required to validate 

any warranty service. 

 

Warranted against manufacturer or 

workmanship defects from date of 

purchase with copy of receipt: 

 

Homeowner Usage: Sprayer-One Year and Pump-Two Years. 

 

Commercial Usage: Sprayer and Pump-90 Days.

 

Summary of Contents for 15-2N-ATV-GS











Reviews: